NIST’s Antenna Evaluation Method Could Help Boost 5G Network Capacity and Cut Costs
December 11, 2018 | NISTEstimated reading time: 2 minutes
Researchers at the National Institute of Standards and Technology (NIST) have developed a method for evaluating and selecting optimal antenna designs for future fifth-generation (5G) cellphones, other wireless devices and base stations.
Image Caption: NIST researcher Jelena Senic drives a robot used to measure the performance of different antenna beam patterns. The mobile platform enables researchers to position a wireless channel sounder that includes (top to bottom) an array of 16 receive antennas, the receiver, timing circuitry, a signal digitizer and a battery for untethered field operations.
The new NIST method could boost 5G wireless network capacity and reduce costs.
5G systems will avoid crowded conventional wireless channels by using higher, millimeter-wave frequency bands. Transmissions at these frequencies lose a lot of energy along the way, which weakens received signal strength. One solution is “smart” antennas that can form unusually narrow beams—the area in space where signals are transmitted or received—and rapidly steer them in different directions.
Antenna beamwidth affects wireless system design and performance. NIST’s new measurement-based method allows system designers and engineers to evaluate the most appropriate antenna beamwidths for real environments.
“Our new method could reduce costs by enabling greater success with initial network design, eliminating much of the trial and error that is now required,” NIST engineer Kate Remley said. “The method also would foster the use of new base stations that transmit to several users either simultaneously or in rapid succession without one antenna beam interfering with another. This, in turn, would increase network capacity and reduce costs with higher reliability.”
This is the first detailed measurement-based study of how antenna beamwidth and orientation interact with the environment to affect millimeter-wave signal transmission. In the technique, NIST measurements covering a broad range of antenna beam angles are converted into an omnidirectional antenna pattern covering all angles equally. The omnidirectional pattern can then be segmented into narrower and narrower beamwidths. Users can evaluate and model how antenna beam characteristics are expected to perform in specific types of wireless channels.
An engineer could use the method to select an antenna that best suits a specific application. For example, the engineer may choose a beamwidth that is narrow enough to avoid reflections off certain surfaces or that allows multiple antennas to coexist in a given environment without interference.
To develop the new method, the NIST team collected experimental data in a hallway and lobby of a NIST research building, using a special robot loaded with a customized channel sounder and other equipment. A channel sounder collects data that capture the signal reflections, diffractions and scattering that occur between a transmitter and receiver. Many such measurements can be used to create a statistical representation of the radio channel, to support reliable system design and standardization.
NIST study results confirm that narrow beams can significantly reduce signal interference and delays, and that an optimized beam orientation reduces energy loss during transmissions. For example, the time interval during which signal reflections arrive (a metric called RMS delay spread) dropped dramatically from 15 nanoseconds (ns) to about 1.4 ns as antenna beamwidth was reduced from omnidirectional (360 degrees) to a narrow 3 degrees or so-called pencil beam.
Future research will include extending the method to different environments and analysis of other wireless channel characteristics.
Suggested Items
embedded world 2024: Rohde & Schwarz Presents its Cutting-edge Test Solutions for Embedded Systems
03/27/2024 | Rohde & SchwarzEmbedded systems are the foundation of today’s electronic devices, spanning sectors as diverse as consumer electronics, telecommunications, industrial, medical, automotive and aerospace applications.
Reassessing Surface Finish Performance for Next-gen Technology, Part 2
03/04/2024 | Frank Xu, PhD and Martin Bunce of MacDermid Alpha, and John Coonrod of Rogers Corp.The introduction of 5G/6G has created a growing demand for faster rates of data transfer and operation at higher frequencies, pushing signals to travel toward the outer edges of conductors. As a result, the surface finish applied over the copper circuitry is now gaining more attention.
Beyond Design: Embedded Capacitance Material
02/22/2024 | Barry Olney -- Column: Beyond DesignEmbedding components into the multilayer PCB substrate can have many benefits, including reduced board size and improved signal integrity. However, embedded capacitance material (which is not really a component but rather part of the substrate) can improve power integrity dramatically by reducing AC impedance and generally enhancing the performance of the product. It takes up no additional space, is easy to implement (because it is compatible with standard FR-4 processes), and can be cost-effective.
RoBAT Brings TDR Test to Bare and Assembled PCBs
02/19/2024 | Andy Shaughnessy, Design007 MagazineIn an interview at DesignCon, Gregory Miczek, global applications manager with RoBAT, discussed the company’s background and its expansion path from backplane defect analyzers to TDR testers for high-tech bare and assembled boards.
Connect the Dots: Controlled Impedance and Calculations for Microstrip Structures
12/28/2023 | Matt Stevenson -- Column: Connect the DotsModern high-speed and RF PCB design is an exciting field but comes with its own set of challenges. Signal integrity, performance, and crosstalk become major concerns. Designers for these types of projects need to learn how to control electromagnetic interference (EMI) and compatibility (EMC), which means utilizing some interesting math and calculations.