PMI in May Drops to Lowest since September 2009
June 4, 2019 | IHS MarkitEstimated reading time: 6 minutes
May survey data signalled only a marginal improvement in the health of the U.S. manufacturing sector. The headline PMI fell to its lowest level since September 2009 as output growth eased and new orders fell for the first time since August 2009. Weak demand conditions and ongoing trade tensions led firms to express the joint-lowest degree of confidence regarding future output growth since data on the outlook were first collected in mid-2012. At the same time, employment rose at the slowest rate since March 2017 and backlogs of work were unchanged. Meanwhile, inflationary pressures eased further, with both input costs and output prices increasing at softer rates.
The seasonally adjusted IHS Markit final U.S. Manufacturing Purchasing Managers’ Index™ (PMI™) posted 50.5 in May, down from 52.6 in April. The latest headline figure signalled only a slight improvement in operating conditions, with the latest reading the lowest since September 2009. The data for the second quarter so far have indicated a distinct slowdown in the manufacturing sector compared to the first three months of 2019.
A key factor weighing on the headline reading was the softest expansion of output since June 2016. May data signalled only a marginal rise in production that was often linked to clearing backlogs of previously-placed orders.
At the same time, manufacturers signalled the first decline in new orders since August 2009. Though only fractional, survey respondents stated that weak client demand drove the fall. Some firms also noted that customers were postponing orders due to growing uncertainty about the outlook. Similarly, new business from abroad contracted for the first time since July 2018, albeit at a marginal rate.
Consequently, manufacturers exhibited a lower degree of confidence towards output over the coming year. Expectations for growth dipped to their joint-lowest since the series began in July 2012, as firms highlighted concerns surrounding ongoing trade tensions and a growing trend of customers postponing new orders, especially among large clients.
On the price front, cost burdens increased at only a modest rate in May. The rise was the slowest since July 2017, with reports of tariffs driving costs higher being countered by increased competition among suppliers. Subsequently, firms increased their factory gate charges only marginally amid efforts to remain competitive.
Meanwhile, firms signalled a further increase in employment in May. The upturn was commonly linked to the replacement of voluntary leavers and retirees. Nonetheless, the expansion was the slowest since March 2017 amid tight labour market conditions.
Finally, purchasing activity was broadly unchanged in May as firms indicated greater efforts to use current inventories for production and increased efforts to readjust stock levels in light of softer demand conditions.
Commenting on the PMI data, Chris Williamson, Chief Business Economist at IHS Markit said:
"May saw US manufacturers endure the toughest month in nearly ten years, with the headline PMI down to its lowest since the height of the global financial crisis. New orders are falling at a rate not seen since 2009, causing increasing numbers of firms to cut production and employment. At current levels, the survey is consistent with the official measure of manufacturing output falling at an increased rate in the second quarter, meaning production is set to act as a further drag on GDP, with factory payroll numbers likewise in decline.
“While tariffs were widely reported as having dampened demand and pushed costs higher, both producers and their suppliers often reported the need to hold selling prices lower amid lacklustre demand. While this bodes well for inflation, profit margins are clearly being squeezed as a result.
“With future optimism sliding sharply lower in May, risks to near-term growth have shifted further to the downside.
“While companies of all sizes are struggling, the biggest change since the strong growth seen late last year is a deteriorating performance among larger companies, where surging order book growth just a few months ago has now turned into contraction, the first such decline seen in the series’ ten-year history.”
Page 1 of 2
Suggested Items
ViTrox Pioneering the Future of Smart Manufacturing at NEPCON China 2024
04/18/2024 | ViTroxViTrox, which aims to be the World’s Most Trusted Technology Company, is pleased to announce its participation in the NEPCON China 2024 at Booth #1H27 at Shanghai World Expo Exhibition & Convention Center from 24-26 April 2024.
Renesas Commences Operations of Kofu Factory as Dedicated 300-mm Wafer Fab for Power Semiconductors
04/15/2024 | RenesasRenesas Electronics Corporation, a premier supplier of advanced semiconductor solutions, today announced that it has started operations at its Kofu Factory, located in Kai City, Yamanashi Prefecture, Japan.
Aegis Software and JUKI Extend Reseller Relationship, Marking Over 23 Years of Collaboration
04/11/2024 | Aegis SoftwareAegis Software, a global provider of Manufacturing Execution System (MES) software, announces that JUKI Automation, a world-leading provider of automated assembly products and systems and subsidiary of JUKI Corporation, has renewed their reseller relationship with Aegis Software.
TT Electronics Awarded Contract with Kongsberg Defence and Aerospace
04/11/2024 | TT ElectronicsTT Electronics, a leading provider of global manufacturing solutions and engineered technologies, announced today that its Fairford UK business has been awarded a new contract with long-standing customer Kongsberg Defence and Aerospace (Kongsberg) for the production of complex cable harness solutions.
Connect the Dots: Designing for Reality: Prioritizing Manufacturability
04/11/2024 | Matt Stevenson -- Column: Connect the DotsRealistic PCB designs should prioritize manufacturability and reliability of the PCB as well as meet the other design requirements. To do so, one must account for the production variables associated with individual manufacturing partners. Understanding and creating robust PCB designs, especially in terms of board manufacturing, requires a lot of attention to detail. When more detail is included in the design, the manufacturing process goes more smoothly, and process yields are higher.