Researchers Report a New Way to Produce Curvy Electronics
September 27, 2019 | University of HoustonEstimated reading time: 2 minutes
Contact lenses that can monitor your health as well as correct your eyesight aren’t science fiction, but an efficient manufacturing method—finding a way to produce the curved lenses with embedded electronics—has remained elusive.
Until now. A team of researchers from the University of Houston and the University of Colorado Boulder has reported developing a new manufacturing method, known as conformal additive stamp printing, or CAS printing, to produce the lenses, solar cells and other three-dimensional curvy electronics. The work, reported in the journal Nature Electronics, demonstrates the use of the manufacturing technique to produce a number of curvy devices not suited to current production methods. The work is also highlighted by the journal Nature.
“We tested a number of existing techniques to see if they were appropriate for manufacturing curvy electronics,” said Cunjiang Yu, Bill D. Cook Associate Professor of Mechanical Engineering at the University of Houston and corresponding author on the paper. “The answer is no. They all had limitations and problems.”
Instead, Yu, who is also a principal investigator with the Texas Center for Superconductivity at UH, and his team devised a new method, which they report opens the door to the efficient production of a range of curvy electronic devices, from wearables to optoelectronics, telecommunications and biomedical applications.
“Electronic devices are typically manufactured in planar layouts, but many emerging applications, from optoelectronics to wearables, require three-dimensional curvy structures,” the researchers wrote. “However, the fabrication of such structures has proved challenging due, in particular, to the lack of an effective manufacturing technology.”
Existing manufacturing technologies, including microfabrication, don’t work for curved, three-dimensional electronics because they are inherently designed to produce two-dimensional, flat electronic devices, Yu said. But increasingly, there is a need for electronic devices that require curvy, 3-D shapes, including smart contact lenses, curved imagers, electronic antennas and hemispherical solar cells, among other devices.
These devices are small—ranging in size from millimeters to centimeters—with accuracy within a few microns. Recognizing that, Yu and the other researchers proposed the new fabrication method, conformal additive stamp printing, or CAS printing.
CAS printing works like this: An elastomeric, or stretchy, balloon is inflated and coated with a sticky substance. It is then used as a stamping medium, pushing down on pre-fabricated electronic devices to pick up the electronics and then print them onto various curvy surfaces. In the paper, the researchers describe using the method to create a variety of curvy devices, including silicon pellets, photodetector arrays, small antennas, hemispherical solar cells and smart contact lenses.
The work was performed using a manual version of the CAS printer, although the researchers also designed an automated version. Yu said that will make it easy to scale up production.
In addition to Yu, co-authors include Kyoseung Sim, Song Chen, Zhoulyu Rao, Jingshen Liu, Yuntao Lu, Seonmin Jang, Faheem Ershad and Ji Chen, all with UH, and Zhengwei Li and Jianliang Xiao, both with the University of Colorado Boulder.
This work was supported by National Science Foundation.
Suggested Items
IMI Taps New Opportunities to Sustain Grit in China
03/28/2024 | IMIIntegrated Micro-Electronics, Inc. (IMI), Joey S. Bantatua, IMI China’s head of operations and general manager was recently interviewed by Asia Electronics Industry (AEI) magazine where he talked about the prospects of the country both as a market and a production hub.
Kimball Electronics Publishes Annual Sustainability Disclosures with its 2023 Guiding Principles Report
03/28/2024 | BUSINESS WIREKimball Electronics, Inc. published its annual sustainability disclosures in its 2023 Guiding Principles Report, themed “How We Are Winning Together The Kimball Way.”
iNEMI Webinar: Humidity Robustness and Insulation Coordination for e-Mobility
03/27/2024 | iNEMIThis webinar is a follow-up to the recent Seminar on Humidity Robustness and Insulation Coordination for e-Mobility, organized by iNEMI and ZESTRON Europe and supported by the ECPE.
Electronics Industry Sentiment Rises in March
03/27/2024 | IPCIPC releases March 2024 Global Sentiment of the Electronics Supply Chain Report
Mycronic to Showcase More Versatile, High-productivity Assembly Solutions at IPC APEX EXPO 2024
03/27/2024 | MycronicMycronic, the leading Sweden-based electronics assembly solutions provider, will continue to respond to growing customer demand for high-flexibility, high-productivity solutions for zero-defect PCB assembly at IPC APEX EXPO 2024 in Anaheim, CA on April 9 - 11.