-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Ledia 6 Direct Imaging System Offers Enhanced Speed and Precision
December 29, 2019 | Pete Starkey, I-Connect007Estimated reading time: 3 minutes
I recently met with Ucamco’s Michel Van den heuvel, imaging product group director, to discuss the benefits of the Ledia 6 direct imaging system, which was introduced earlier this summer and features scan-alignment and improvements in registration and positioning accuracy.
Pete Starkey: Michel, it’s great to see you again.
Michel Van den heuvel: Hi, Pete. I’m happy to see you.
Starkey: One of your specialties is the Ledia direct imaging system, and I understand that there have been some new developments lately. Can you bring us up-to-date with the latest advances?
Van den heuvel: After Ledia 5, SCREEN Graphic and Precision Solutions introduced Ledia 6, which is a further improvement and development of the existing Ledia 5. Based on the feedback they had from customers, they have made further enhancements. One of the main improvements is a new camera-registration system. On the existing Ledia 5, they used step-alignment, which means that the table stops, switches on the light of the registration camera, and takes a picture of the fiducial, and then the table moves to the next fiducial and takes a picture again.
In the Ledia 6, they have introduced scan-alignment. The table moves at a constant speed and does not stop any more. When it needs to take a fiducial, it switches on the light and quickly takes the picture—it’s like a stroboscope effect—and switches the light on and off while the table keeps moving. Through software, they stitch all these pictures together and know exactly where all the fiducials are. It goes much faster because the table doesn’t need to stop.
Starkey: How accurately can you hold registration with this system?
Van den heuvel: Registration and positioning accuracy go together because, eventually, the result that the customer can see on the panel is positioning accuracy. With Ledia 6, we have improved positioning accuracy by 10% compared to the Ledia 5, and also improved registration accuracy by 20%.
In addition to the scan-alignment system, the width of the registration cameras has been doubled in size. Take the example where a solder mask panel has been routed after the panel has been made. This can influence not only the exact size but also the position of the fiducials towards the edge of the panel. With a smaller camera, this could previously result in sometimes missing a fiducial. The double-width scan-alignment camera will completely resolve this issue.
Another improvement, together with the scan-alignment, is that if you have multiple step-and-repeat single PCBs on the panel, and the fiducials of adjacent PCBs are within 12 millimeters of each other, our front-end software will automatically combine these fiducials and scan them with one camera in one go. Instead of doing two scans, you can combine it in one scan. Especially for step-and-repeats of panels, such as BGAs, this greatly improves scan-alignment time.
A further improvement involves new, stronger light sources that we built into the imaging heads. We made a change to the optics to make them capable of handling this stronger light source, which results in up to 25–30% throughput improvement. And the less sensitive is the material, the bigger the improvement you will notice.
Starkey: In a typical case with a solder mask, what would be the exposure time?
Van den heuvel: Exposing time depends on the panel. For 100 millijoules, the exposing time for a 610 x 457-millimeter [24 x 18-inch] panel side would be around 23.7 seconds compared to the previous 30.3 seconds, including four-point registration. Whenever you gain 6.6 seconds in a single run, that is a huge improvement.
Starkey: And your light sources can be tuned to achieve the optimum wavelength for the photo-initiator system in the solder mask?
Van den heuvel: Yes. The way the optical heads are designed, we can 100% independently adjust the different main wavelengths that we use: 365, 385, and 405 nanometers. We can independently adjust each wavelength from zero to 100% and tune to the solder mask at hand and achieve the best possible sidewall, reducing undercut to a minimum.
Starkey: Have you already launched the Ledia 6 into the market?
Van den heuvel: Yes, we have. The first systems in Europe have been sold this year, and two of them have already been installed at ICS in Italy and Optiprint in Switzerland. The results have been as we expected, and our clients are delighted with the outcome. Next week, we will install a third one at Eurocircuits in Hungary.
Starkey: That is splendid! I wish you every success with the system. Thank you very much for your time.
Van den heuvel: Thank you, Pete.
Suggested Items
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.
Empowering Electronics Assembly: Introducing ALPHA Innolot MXE Alloy
04/16/2024 | MacDermid Alpha Electronics SolutionsIn the rapidly evolving electronics industry, where innovation drives progress, MacDermid Alpha Electronics Solutions is committed to setting a new standard. Today, we are pleased to introduce ALPHA Innolot MXE, a revolutionary alloy meticulously engineered to address the critical needs of enhanced reliability and performance in modern electronic assemblies.
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
Inkjet Solder Mask ‘Has Arrived’
04/10/2024 | Pete Starkey, I-Connect007I was delighted to be invited to attend an interactive webinar entitled “Solder Mask Coating Made Easy with Additive Manufacturing,” hosted by SUSS MicroTec Netherlands in Eindhoven. The webinar was introduced and moderated by André Bodegom, managing director at Adeon Technologies, and the speakers were Mariana Van Dam, senior product manager PCB imaging solutions at AGFA in Belgium; Ashley Steers, sales manager at Electra Polymers in the UK; and Dr. Luca Gautero, product manager at SUSS MicroTec Netherlands.
TE Connectivity Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/09/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that TE Connectivity has finalized the purchase of a Pulsar solderability testing system.