IPC Europe Shares Technical Education and Standards Awareness
April 22, 2020 | Pete Starkey, I-Connect007Estimated reading time: 4 minutes
Against a background of COVID-19 uncertainty and unprecedented challenges, but recognising the vital importance of continuing to educate engineers and share the knowledge and skills required to manufacture boards and assemblies of the highest yields and reliability, the IPC Europe team hosted a technical webinar for the European electronics industry, featuring the expertise of two of I-Connect007’s regular columnists: Mike Carano and Jan Pedersen.
Introduced by Sanjay Huprikar, IPC vice president of solutions, and Philippe Léonard, director of operations IPC Europe, Carano shared some keen insights into troubleshooting and defect analysis for PCBs as VP of technology and business development for RBP Chemical Technology.
With more than 40 years in the industry and 34 years of active participation in IPC, Carano is currently co-chair of the IPC Technology Roadmap executive committee and member of the IPC Hall of Fame and recipient of the Dieter Bergman IPC Fellowship Award. He was an accomplished and skilful teacher, generously sharing a slice his encyclopaedic knowledge and experience with no hint of condescension. Carano gave a concise overview of the materials, chemical processes, and equipment parameters that impact PCB quality, focusing on defect analysis and troubleshooting.
Carano stressed that—because PCB fabrication was an integrated process involving a maze of inter-related chemical, mechanical and imaging steps—a defect might not show up in the process that caused it. As an example, a defect or process indicator that manifested itself in nickel-gold plating might have originated in the solder mask or copper plating step, so it was essential to understand the upstream and downstream processes. He explained the mechanism of the troubleshooting procedure, recommended avoiding the “head-in-the-sand syndrome,” and commented: “Troubleshooting is a science. Follow the evidence. Common sense usually applies.”
Carano briefly explained how to identify and correct the control processes that adversely affected circuit board quality, how to establish the root cause of potential defects to minimise and prevent loss of quality; how to recognise the inter-relationships of PCB materials, processes, and equipment; and how those relationships affected the quality of PCBs and assemblies. He discussed root causes and corrective actions for defects such as interconnect separation, delamination, wedge voids, plating folds, microvoids, surface pitting, and hole-wall pull-away, and also considered electrodeposition defects, solderability and assembly-related issues, such as outgassing, black pad, creep corrosion, and blow holes.
Carano covered so much ground in his 25-minute slot and 56 PowerPoint slides that I admit I struggled to take it all in. But he certainly emphasised the principles of effective troubleshooting and gave an indication of the enormity of the topic in the context of PCB fabrication and assembly. Carano’s presentation was a preview of a comprehensive distance-learning course offered by IPC, with six two-hour sessions spread over three weeks, taught by himself and utilising interactive webinars, on-demand recordings, and job-specific exercises. Details can be found on IPC’s website.
Introduced as “The Exemplary IPC Member,” PCB Norseman Jan Pedersen, senior technical advisor at Elmatica and chair of numerous standards development committees, gave an update on IPC standards development activities in Europe directed at the automotive and medical sectors. Specifically, he discussed the Automotive Applications Addendum to IPC-6012D qualification and performance specification for rigid printed boards and the IPC-6012 and 6013 Medical Addendum aimed at strengthening the reliability and consistency of PCB product qualification and acceptance for medical devices.
Pedersen explained the justification for the Automotive Addendum. Automotive electronics represented a unique combination: life-critical systems, produced in high volumes, and operating in harsh environments. The aim was to establish a globally-accepted set of reliability-related requirements. He made it clear that the addendum was intended not to be a standalone document, but to be recognised as automotive-electronics-specific requirements in addition to or in place of IPC-6012E Class 3 requirements. It was planned to launch the addendum as IPC-6012EA in the spring of 2021.
The special requirements in addition to IPC-6012 would relate to: visual examination, lifted lands after thermal stress, hole size, hole pattern and pattern feature accuracy, preconditioning before bow and twist assessment, defects along the edges of rectangular surface mount lands, wicking, hole wall separation after thermal stress, solder mask thickness, cleanliness of the delivered PCB, acceptance testing frequency, and recommended suitability and reliability testing. Pedersen gave examples of limits on lifted lands (3.3.4), AOI requirements (3.5.1 through 3.5.4.8), limits on wicking (3.6.2.1), cleanliness test methods (3.9), and frequency of process control microsections. Several other items were scheduled for discussion at the forthcoming task group web meeting.
Automotive-specific standards had also been developed for electronic assemblies. The J-STD-001/IPC-610 Automotive Addendum launched in February 2020. IPC J-STD-001GA / IPC-A-610GA combined performance requirements and acceptability in one document—a first for IPC. And IPC-9797 was defining characterisation, qualification, and acceptance requirements for compliant press-fit pin technology for the automotive and aerospace industries.
Pedersen also chaired the task group for the Medical Addendum to IPC-6012 and IPC-6013. IPC-6012 EM would be the first-ever standard for PCBs in medical devices and would provide consistency of PCB product qualification and acceptance beyond IPC Class III to demonstrate suitability for medical devices and give a high degree of assurance of the reliability and durability of the PCB. IPC-6012EM was currently at the ballot stage, with its flex and flex-rigid counterpart IPC-6013EM following closely behind it.
Traceability was fundamental to the automotive and medical sectors. A revision of IPC-1782 Standard for Manufacturing and Supply Chain Traceability of Electronic Products was currently at the ballot stage and now included traceability for printed boards in addition to the electronic production. The IPC-6012 Automotive Addendum would be linked to IPC-1782A with a requirement for traceability levels related to reliability requirements.
Pedersen’s presentation demonstrated the power of industry volunteers collaborating to solve technical challenges. And this was echoed by Sanjay Huprikar’s acknowledgement that IPC’s most important asset was its thousands of global volunteers.
It was an informative hour. Many thanks to the IPC Europe team for putting it together and for engaging two leading industry experts to deliver the content.
Suggested Items
Indium Corporation to Present, Exhibit at EPP InnovationsFORUM
03/28/2024 | Indium CorporationIndium Corporation is set to present and exhibit at EPP InnovationsFORUM, one of Europe’s premier single-day electronics manufacturing forums, on April 17 in Leinfelden-Echterdingen, Germany. Topic areas for 2024 will include AI, automation, sustainability, and quality.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
Indium Corporation, Industry Partners to Showcase Products “Live@APEX”
03/26/2024 | Indium CorporationIndium Corporation®, in cooperation with its industry partners, will feature its proven solder solutions live on the show floor throughout IPC APEX Expo from Apr. 9‒11 in Anaheim, Calif., U.S.
ITW EAE Wins New Product Introduction Award for Electrovert® Wave Soldering Machine Deep Wave
03/26/2024 | ITW EAEITW EAE is proud to announce that it has earned a 2024 New Product Introduction (NPI) Award for Electrovert’s Deep Wave option for wave soldering machines. This new, innovative system provides the ability to pump up to a 20 mm wave height.
Mek's Next-Gen AOI Technology Takes Center Stage at IPC APEX EXPO 2024
03/19/2024 | MEKMek is excited to announce its presence at IPC APEX EXPO, North America's largest electronics manufacturing event, in Anaheim, California, from April 6-11, 2024. Attendees are invited to visit Mek at booth #1433 to explore the latest AOI technology offerings.