-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Beyond Design: DDR3/4 Fly-by vs. T-topology Routing
June 1, 2016 | Barry Olney, In-Circuit Design Pty LtdEstimated reading time: 1 minute
JEDEC introduced fly-by topology in the DDR3 specification for the differential clock, address, command and control signals. The advantage of fly-by topology is that it supports higher-frequency operation, reduces the quantity and length of stubs and consequently improves signal integrity and timing on heavily loaded signals. Fly-by topology also reduces simultaneous switching noise (SSN) by deliberately causing flight-time skew, between the address group and the point-to-point topology signals, of the data groups. To account for this skew, the DDR3/4 controller supports write leveling. The controller must add the write leveling delays to each byte lane to maintain the strobe to clock requirement at the SDRAMs.
T-topology can be challenging to route, particularly double T-topology with four back-to-back SDRAMs, but it can be advantageous when using multi-die packages. The fly-by topology used in Figure 3 is much easier to route but does not work well with high-capacitance loads, such as LPDDR3 DDP (double die package) and QDP (quad die package) devices. IC fabricators basically arrange dies in parallel to increase package density which can also increase input capacitance by up to four times. Excessive ring-back is often present in the first few nodes of the daisy chain.
This is the reason why the T-topology was developed. However, if you are supporting only SDP (single die package) devices, then the fly-by is the most straightforward approach. It doesn't matter which topology you use, though—both fly-by and double T-topologies should work fine. If you are using a DDP device, then double-T topology works better than fly-by in terms of delivering a better system margin.
During a write cycle, using the fly-by topology, data strobe groups are launched at separate intervals to coincide with the clock arriving at memory components on the SODIMM or PCB, and must meet the timing parameter between the memory clock and DQS defined as tDQSS of ± 0.25 tCK. The PCB design process can be simplified using the leveling feature of the DDR3/4. The fly-by, daisy chain topology increases the complexity of the controller design to achieve leveling but fortunately, greatly improves performance and eases board layout for DDR3/4 designs.
To read this entire article, which appeared in the April 2016 issue of The PCB Design Magazine, click here.
Suggested Items
Cadence, TSMC Collaborate on Wide-Ranging Innovations to Transform System and Semiconductor Design
04/25/2024 | Cadence Design SystemsCadence Design Systems, Inc. and TSMC have extended their longstanding collaboration by announcing a broad range of innovative technology advancements to accelerate design, including developments ranging from 3D-IC and advanced process nodes to design IP and photonics.
Ansys, TSMC Enable a Multiphysics Platform for Optics and Photonics, Addressing Needs of AI, HPC Silicon Systems
04/25/2024 | PRNewswireAnsys announced a collaboration with TSMC on multiphysics software for TSMC's Compact Universal Photonic Engines (COUPE). COUPE is a cutting-edge Silicon Photonics (SiPh) integration system and Co-Packaged Optics platform that mitigates coupling loss while significantly accelerating chip-to-chip and machine-to-machine communication.
Siemens’ Breakthrough Veloce CS Transforms Emulation and Prototyping with Three Novel Products
04/24/2024 | Siemens Digital Industries SoftwareSiemens Digital Industries Software launched the Veloce™ CS hardware-assisted verification and validation system. In a first for the EDA (Electronic Design Automation) industry, Veloce CS incorporates hardware emulation, enterprise prototyping and software prototyping and is built on two highly advanced integrated circuits (ICs) – Siemens’ new, purpose-built Crystal accelerator chip for emulation and the AMD Versal™ Premium VP1902 FPGA adaptive SoC (System-on-a-chip) for enterprise and software prototyping.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
IPC Design Competition Champion Crowned at IPC APEX EXPO 2024
04/24/2024 | IPCAt IPC APEX EXPO 2024 in Anaheim, California, five competitors squared off to determine who was the best of the best at PCB design.