Elementary, Mr. Watson: APEX EXPO—The Ghosts Past, Present, and Future
Beyond Design: Demystifying Common‑Mode Radiation
Connect the Dots: Designing for the Future of Manufacturing Reality—Strip-Etch-Strip
Brooks' Bits: Your Traces Have Hot Spots!
August 24, 2016 | Douglas G. Brooks, PhDEstimated reading time: 1 minute
Your traces have hot spots. At least, those that carry a moderate current do. Surprised? Well, I was a little surprised, too, when I looked at this a little more closely.
One chapter in my recent book focuses on fusing current. It contains the image (Figure 1), captured on video, which shows a 20 mil wide trace that had been heated for about 15 minutes, just at the moment of fusing. There are several interesting things in this image, especially how the smoke is blown out from under the trace at certain points with considerable pressure. But note that the trace fuses at a point, not everywhere along the trace. It is clear from observation that the trace is much hotter at some points than at others.
Figure 2 appeared in a separate article published in 2010. (It has been enhanced after some collaboration with the author of that article.) The image shows a trace being heated to the melting point. At this stage, the hottest portions of the trace are over 600°C, but other areas remain in the 200°C temperature range.
The reasons for the temperature variation at high temperatures are not too hard to understand. There may be minor contamination under the trace or in the copper that accounts for it. Certainly, at higher temperatures (say above about 300°C) the board may begin to delaminate, severely disrupting its cooling characteristics. There may be small variations in trace width or thickness that help account for the delam, and these effects would be randomly distributed along the length of the trace.
But in a variety of lower-temperature studies, I personally took trace temperature measurements using a small thermocouple. I noticed that if I moved the thermocouple slightly, I would get a different temperature reading. Not by much, maybe 1.0° or 1.5°C. This is more than the resolution of the thermocouple, but not enough for me to be satisfied that the differences were real. So I began to wonder if these variations in temperature appeared at lower trace temperatures, say in the 40°C. range.
To read this entire article, which appeared in the August 2016 issue of The PCB Design Magazine, click here.
Share on:
Testimonial
"Your magazines are a great platform for people to exchange knowledge. Thank you for the work that you do."
Simon Khesin - Schmoll MaschinenSuggested Items
NCAB Group White Papers: Practical PCB Design Guidance for Manufacturable Results
02/25/2026 | I-Connect007 Editorial TeamThe I-Connect007 Industry Resource Center brings together expert white papers that help engineers and manufacturers navigate today’s design and manufacturing challenges across the PCB lifecycle. NCAB Group contributes a valuable collection of white papers focused on practical PCB design and manufacturability. Drawing on their experience with a global network of production partners, NCAB helps engineers align design intent with fabrication realities: reducing risk while improving consistency and long-term reliability.
Connect the Dots: Designing for the Future of Manufacturing Reality—Strip-Etch-Strip
02/19/2026 | Matt Stevenson -- Column: Connect the DotsThe demand for ultra-high density interconnect (UHDI) PCBs is growing as electronic devices become increasingly advanced. That means we will be creating more designs that need to align with the reality of manufacturing UHDI boards. My last column on this subject focused on plating, and we are ready to discuss the strip-etch-strip (SES) process. With UHDI boards, footprints are smaller and tolerances are tighter. Your big design challenge associated with the SES process involves trace width and spacing control. The etching process can undercut traces and alter their final size.
Powering the Future: From Thick-Film to DBC—Understanding the Evolution of Ceramic Packaging
02/11/2026 | Brian Buyea -- Column: Powering the FutureCeramic packaging has quietly powered the electronics revolution for more than half a century. From the earliest thick-film hybrids to today’s direct bond copper (DBC) substrates and metallized aluminum nitride, every step forward in ceramic technology has pushed the limits of reliability, power density, and performance. It’s essential for every design engineer building the next generation of electronic systems to understand this evolution.
Fresh PCB Concepts: Cost Stability in a Period of Copper and Gold Volatility
02/12/2026 | Team NCAB -- Column: Fresh PCB ConceptsAnyone who works with PCBs in any capacity right now can feel that copper and laminate prices are not stagnant, gold price is increasing even faster, and the impact shows up quickly on PCB quotations. For many design teams, this feels like a force outside their control. Raw materials go up, and the board cost goes with it. I want to highlight that many of these swings are manageable.
Connect the Dots: The Future of Designing for Reality—Pattern Plating
02/05/2026 | Matt Stevenson -- Column: Connect the DotsLast month, I discussed the outer-layer imaging process and offered tips for designers to help ensure smooth manufacturing and high-quality output. The next step in the manufacturing process is copper pattern plating, where fabrication can be tricky, and design precision is even more important. The board is now ready to have the copper traces, through-holes, vias, pads, and other elements specified in the original CAD design plated to copper thickness requirements. I will identify some key design considerations for pattern plating, break down the process, and offer design tips for a successful outcome.