Ventec USA Prepares for Growth
April 17, 2014 | Pete Starkey, I-Connect007Estimated reading time: 3 minutes
Starkey: Ray, I’m impressed by your CV. In my opinion, you have the ideal background for the job.
Young: What I can offer is 40 years’ experience in PCB fabrication. I started straight from high school and worked my way up the ladder from hands-on, shop-floor processing through plant management and general management to senior operations executive roles. And I have worked for some big-name companies supplying the high-technology, high-reliability electronics industry. I’ve got a lot of experience of AS9100C aerospace industry quality management systems, a lot of confidence in Ventec’s materials from a user viewpoint, and a clear appreciation of the high level of support that Southern Californian PCB fabricators demand of their suppliers.
Starkey: And what are your plans for the expansion of the Fullerton service centre?
Young: As well as doubling our panel-sawing capacity and installing clean-room cutting and packaging for pre-pregs, we plan to streamline our distribution channel to give the best possible value to customers in terms of quality, technology, service, and cost. We understand the high-mix, quick-turn nature of our market and can ship almost everything same-day.
Having a press facility, we can cater for the odd-ball requirement--whatever the diversity of material we hold in stock, someone will always want what we don’t have on the shelf. So we can manufacture small quantities of specialist and odd-form laminates, including VT-901 polyimide and a full range of IMS materials, on short lead times. And we’re not afraid of hard work!
Starkey: Thanks, Ray, Jack--a final word from you?
Pattie: It goes without saying that our absolute aim is to give the very best in customer satisfaction. Ventec USA’s outstanding reputation for responsive service and technical back-up continues to grow and we pride ourselves on quality and consistency across a very diverse range of laminate products.
Page 2 of 2Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.