Flex Circuit Shielding Design Options
October 22, 2015 | Mike Morando, PFC Flexible CircuitsEstimated reading time: 4 minutes
Figure 3: Silver paste screened over a coverlay showing the via stitches down to a ground line—another coverlay goes on top to protect the silver.
- EMI Thermoplastic Shielding film—latest technique. This technology is the newest and most flexible shielding technique. The ultra-thin, ultra-flexible materials were developed for the cell phone market. The manufacturing process has been dramatically improved, making it only slightly more expensive than the older technologies. North American flex shops who use this material are pushing their customers in this direction. It is the thinnest and most flexible. It is easy to apply and creates a 360 degree shield similar to a silver paste or stitched copper via.
Figure 4: Material stack of the thermoplastic shielding film.
Figure 5: Thermoplastic shielding film applied to circuits. Easy for your vendor to apply, but material is still expensive.
Shielding—Design for Manufacturing—a Review of what we learned
Most of the North American flex suppliers can provide all four solutions mentioned below, but they will steer you to the technique they are most comfortable with. The most important design decisions for shielding flex circuits are flexibility/bendability and cost.
Here are my impressions:
- Adding layers of copper to shield, while adding potentially excellent shielding characteristics, adds cost, weight and thickness, and can prove to be a disaster when trying to bend the circuit. This method requires via stitching to prevent “leakage.”
- Adding cross-hatch layers can provide excellent shielding characteristics again, but still adding layers, weight, and will affect flexibility. This also requires via stitching to prevent “leakage.”
- Conductive paste allows better flexibility and lighter weight, and better coverage of shielding. Requires via stitching.
- Thermoplastic shielding film is slick stuff. Easy to apply, thin, light, and bendable. It allows no side leakage. It was originally made for cellphones so the material has been proven, but is more expensive (by 25%) than shielding with normal/older techniques.
Mike Morando is VP of sales and marketing for PFC Flexible Circuits Limited.
Page 2 of 2Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.