Which IPC-A-610 Class is Best for Your PCBA?


Reading time ( words)

When you think about what makes a good electronics assembly, what are the most common expectations that come to mind? If the assembly works as intended, then surely that indicates a certain level of acceptability, right? But what about the product's longer-term reliability? And what if you'd also like it to look good too?

Printed circuit board assembly (PCBA) is a surprisingly complex thing. There’s the PCB itself with all of its materials, finishes, and various components, and the solder that holds everything together. Within that, there’s also a fair amount of scope for things to be good, bad, or somewhere in between.

For many electronics manufacturing services (EMS) providers, IPC-A-610: Acceptability of Electronic Assemblies is the agreed standard that we use to define what's acceptable and what's not in the world of PCBA production. The standard is comprised of three Classes: 1, 2, and 3. As an original equipment manufacturer (OEM), it’s important that you're clear on the basic principles that separate those classes so that you have a clear and realistic expectation of what the results are going to be.

Class 1

The lowest IPC-A-610 class, Class 1, is the most lenient when it comes to making allowances for potential defects. When we think of the functionality of the electronics assembly within a simple toy, for example, the PCBA is likely to be hidden well away inside the body of the item, so the quality of the solder joints or component positions may not be such a high priority. The product is also likely to be manufactured to very tight margins (read "as cheaply as possible"). So, as long as the item still functions as expected and its operational life sits within an acceptable timeframe, then that will probably be sufficient.

Class 2

Class 2 is typically the most requested for non-critical electronic assemblies where longer-term reliability is desirable, but perhaps not essential. Class 2 still allows for a certain degree of imperfection. Surface-mount components that have been placed slightly off pad, for instance, are usually still fine electrically and mechanically even though they may look wrong aesthetically.

Class 3

The highest standard of IPC-A-610 is Class 3, which means an electronic assembly must be built per all of the IPC criteria. This includes laminate selection, plating thickness, material qualifications, manufacturing processes, and inspection. Typically, Class 3 is aimed at more critical PCB assemblies.

However, achieving that standard may also come at a premium. It might be necessary to slow down the surface-mount machines to ensure the desired placement accuracy, which will mean a longer build time and additional cost. It may also be necessary to make allowance for higher degrees of scrap in cases where materials can’t be reworked or to allow time for extra inspection or additional cleaning.

Working With Your EMS partner

Many would argue that a reliable EMS provider will always aim to manufacture the products they build to the Class 3 standard, regardless. Any EMS provider that is genuinely serious about compliance is also undoubtedly going to have well-established internal training programs to promote awareness within their manufacturing facility. Also, this compliance is likely to extend not just to the inspection of the end products but also to monitoring every process of the build. The best way to achieve this and maintain the standards required will be for them to appoint in-house IPC trainers who will be externally re-certified.

In the majority of cases, the IPC-A-610 standard will suffice, but there may be situations where an OEM prefers to produce their own criteria to either enhance or replace the existing standard. If you do choose to create your own set of guidelines, then it will be important to ensure that your EMS partner is crystal clear about your expectations from the outset. Thus, you should reference your specific criteria on every request for quotation (RFQ) or purchase order that you submit.

Neil Sharp is the director of marketing for JJS Manufacturing.

Share

Print


Suggested Items

Juan Arango on Koh Young’s New U.S. Headquarters

10/27/2019 | Andy Shaughnessy, I-Connect007
At a recent open house, Managing Director Juan Arango talks about his role in the company’s transition from their Arizona facility to a new headquarters located outside of Atlanta, Georgia. Juan details many of the benefits customers can expect, including brand new spaces dedicated to customer demos as well as training.

SMTAI 2019: Chris Bastecki on Low-temperature Solder Challenges and Products

10/14/2019 | Real Time with...SMTAI
Chris Bastecki, director of global PCB assembly at Indium Corporation, discussed challenges of low-temperature solder and the company's new product, Durafuse LT, which provides novel properties and reliability.

Real Time with... SMTAI 2019 Video Interviews

10/09/2019 | Real Time with...SMTAI
The SMTA International Conference and Exhibition 2019, which took place September 22–26, 2019, at the Donald E. Stephens Convention Center in Rosemont, Illinois, concluded successfully. For those of you who were not able to make it to the show, catch our video interviews with the movers and shakers of the electronics industry. We've updated our video presentation for a better experience for our users, so check it out!



Copyright © 2019 I-Connect007. All rights reserved.