Testing Flexible Circuit Assemblies
January 18, 2022 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 3 minutes
I recently spoke with Bert Horner of the Test Connection Inc., about the current state of flex and rigid-flex assembly testing. He explained some of the differences between testing flex and rigid PCBs, the requirements for testing specialties such as high-voltage flex, and the added demands of handling flexible circuits.
Andy Shaughnessy: Bert, tell us about your company and the kinds of test equipment you’ve developed for flexible and rigid-flex circuits. I understand you also provide test services too; do you offer testing for flex?
Bert Horner: The Test Connection Inc., is a full services test engineering and test service that offers different test solutions to test rigid and rigid flex circuits. For prototype or lower volume assemblies, we have flying probe and boundary scan solutions and for the production testing, we have in-circuit test and functional test solutions from partners like Teradyne, Keysight, and National Instruments. TTCI works with fixture partners to offer custom in-house solutions to support and access these challenging assemblies.
Shaughnessy: What are the most common tests for flexible circuit assemblies as well as the biggest challenges? Do high-voltage flexible circuits require a different set of tests than the rest?
Horner: For flying probe testing (FPT), in-circuit testing (ICT) and functional test (FT), the biggest challenge is the tooling for testing the assembly. For the FPT, the handling of the unit under test (UUT) is one of the biggest challenges. This can still be a challenge if the assembly is thin and flimsy, so tooling could still be required. If ICT and FT are done on a fixture or bed-of-nails (BoN), we don’t want to introduce stress to the UUT, so “zero flex” fixturing with finite element analysis (FEA) and strain gauge might be needed, which also adds time and cost. In FT, we see that in high-voltage testing, the biggest challenge is making sure the equipment that will be testing assembly can handle the proper testing requirements. This is about the same set-up as a rigid board, but we haven’t seen too many applications that have this as a requirement.
Shaughnessy: What are some of the biggest differences between testing a flexible circuit and a traditional rigid PCB?
Horner: The physical handling is the biggest challenge in testing flex or rigid-flex circuitry. We often have to develop a custom carrier or handling fixture to test flex or rigid-flex assemblies to help with stability and support.
Shaughnessy: We’ve seen flex and rigid-flex explode in the last decade, and now flex can be found in many household and handheld devices. What trends are you seeing in the world of flex?
Horner: Test access is more of a challenge with accessing the test assemblies through connectors and SMT device “toes” of the solder joints with the assemblies going into two completely different directions. The wearable, handheld, and space applications are getting smaller, but the defense backplanes are in some cases getting larger.
Shaughnessy: How much of your job involves educating new customers about flex and testing?
Horner: We are not doing much with educating the customer on how they want to test flex circuitry, but rather showing them strengths and weaknesses in the test solutions they are choosing or that they have available to test their assemblies. If we are looking at multiple test and inspection tools to get the most coverage on these assemblies, the education becomes about what is best for manufacturing. We both learn preferences of tools that are available.
Shaughnessy: Is there anything else you’d like to add?
Horner: There are more similarities of testing flex circuitry and conventional rigid circuitry, the access, and the handling are where we see the challenge.
Shaughnessy: Thanks for your time, Bert.
Horner: Thank you for the opportunity, Andy.
This interview originally appeared in the January 2022 issue of Design007 Magazine.
Suggested Items
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.
Empowering Electronics Assembly: Introducing ALPHA Innolot MXE Alloy
04/16/2024 | MacDermid Alpha Electronics SolutionsIn the rapidly evolving electronics industry, where innovation drives progress, MacDermid Alpha Electronics Solutions is committed to setting a new standard. Today, we are pleased to introduce ALPHA Innolot MXE, a revolutionary alloy meticulously engineered to address the critical needs of enhanced reliability and performance in modern electronic assemblies.
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
Inkjet Solder Mask ‘Has Arrived’
04/10/2024 | Pete Starkey, I-Connect007I was delighted to be invited to attend an interactive webinar entitled “Solder Mask Coating Made Easy with Additive Manufacturing,” hosted by SUSS MicroTec Netherlands in Eindhoven. The webinar was introduced and moderated by André Bodegom, managing director at Adeon Technologies, and the speakers were Mariana Van Dam, senior product manager PCB imaging solutions at AGFA in Belgium; Ashley Steers, sales manager at Electra Polymers in the UK; and Dr. Luca Gautero, product manager at SUSS MicroTec Netherlands.