Challenges of DFM Analysis for Flex and Rigid-flex Design, Part 2
May 18, 2023 | Mark Gallant, DownStream TechnologiesEstimated reading time: 2 minutes
(Editor’s note: This is the second of a three-part series. To read Part 1, click here.)
Flex and Rigid-Flex: Different Layer Types
Everyday rigid FR-4 PCBs have a well-known layer stackup recipe: dielectrics, PCB conductor layers, plane layers, mask, and silkscreen (nomenclature or legend). More advanced layer types may include embedded or screened components or cavities with bonded bare die.
Flex and rigid-flex stackups include those similar to rigid PCBs, such as dielectrics, conductor, mask, and silkscreen layers, but that is where the similarity ends. There are many additional layer types present for this genre of PCB. They include types like coverlay, adhesive, conductive film, conductive foil, conductive adhesive, bondply, and stiffener.
- Coverlay: An external polyimide film that encapsulates and protects flexible conductor layers.
- Adhesive: Bonding agent used to bond copper foil to a polyimide substrate or coverlay.
- Conductive film: Transparent but electrically conductive film found in LCDs, touchscreens, and other optical applications.
- Conductive foil: Thin sheet of copper or silver commonly applied to a flexible PCB as shielding.
- Conductive adhesive: Adhesive applied for electrical interconnect, thermal or structural bonding applications.
- (Flexible) bondply: A polyimide film, coated both sides with B-staged acrylic adhesive. This is essentially a coverlay with adhesive on both sides.
- Stiffener: Blank FR-4 or other material bonded to flexible materials to add stiffness in a specific area.
These layer types are found in typical flexible PCB stackups. The presence of these layer types is not accounted for in most current DFM analysis. This is one area where specific DFM analysis is required. Rigid DFM analysis can detect issues with a solder mask but cannot be used to detect trace corners in a bend area.
Inter-layer Dependencies
While less common in rigid PCBs, flexible PCBs have many inter-layer dependencies that, if not managed well, may lead to manufacturing issues or field failures. The fabrication process used to bond rigid and flexible layers also has its inter-layer dependencies to be managed. Here are a few examples of inter-layer potential issues.
Squeeze-out
Even with best design considerations and best manufacturing practices, adhesive can “squeeze out” and bleed into unwanted areas on adjacent layers. Coverlay adhesive is a common source of squeeze-out that flows during lamination onto conductors, pads, cavities, fingers, or other features. This requires analysis that compares the size of coverlay exposure against the annular ring of adhesive below it.
To read this entire article, which appeared in the May 2023 issue of Design007 Magazine, click here.
Suggested Items
Indium Corporation to Present, Exhibit at EPP InnovationsFORUM
03/28/2024 | Indium CorporationIndium Corporation is set to present and exhibit at EPP InnovationsFORUM, one of Europe’s premier single-day electronics manufacturing forums, on April 17 in Leinfelden-Echterdingen, Germany. Topic areas for 2024 will include AI, automation, sustainability, and quality.
Reducing Nitrogen Consumption in Convection Soldering with Rehm Thermal Systems' Patented Mechatronic Curtain
03/28/2024 | Rehm Thermal SystemsCurrent developments indicate a need for larger throughput heights due to the trend towards e-mobility, which in turn increases nitrogen consumption for process inertization. Rehm Thermal Systems responds to this issue with an innovative solution: the mechatronic curtain.
Indium Corporation, Industry Partners to Showcase Products “Live@APEX”
03/26/2024 | Indium CorporationIndium Corporation®, in cooperation with its industry partners, will feature its proven solder solutions live on the show floor throughout IPC APEX Expo from Apr. 9‒11 in Anaheim, Calif., U.S.
ITW EAE Wins New Product Introduction Award for Electrovert® Wave Soldering Machine Deep Wave
03/26/2024 | ITW EAEITW EAE is proud to announce that it has earned a 2024 New Product Introduction (NPI) Award for Electrovert’s Deep Wave option for wave soldering machines. This new, innovative system provides the ability to pump up to a 20 mm wave height.
Mek's Next-Gen AOI Technology Takes Center Stage at IPC APEX EXPO 2024
03/19/2024 | MEKMek is excited to announce its presence at IPC APEX EXPO, North America's largest electronics manufacturing event, in Anaheim, California, from April 6-11, 2024. Attendees are invited to visit Mek at booth #1433 to explore the latest AOI technology offerings.