-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueShowing Some Constraint
A strong design constraint strategy carefully balances a wide range of electrical and manufacturing trade-offs. This month, we explore the key requirements, common challenges, and best practices behind building an effective constraint strategy.
All About That Route
Most designers favor manual routing, but today's interactive autorouters may be changing designers' minds by allowing users more direct control. In this issue, our expert contributors discuss a variety of manual and autorouting strategies.
Creating the Ideal Data Package
Why is it so difficult to create the ideal data package? Many of these simple errors can be alleviated by paying attention to detail—and knowing what issues to look out for. So, this month, our experts weigh in on the best practices for creating the ideal design data package for your design.
- Articles
- Columns
- Links
- Media kit
||| MENU - design007 Magazine
Albert Gaines: Design All Comes Down to Documentation
June 28, 2019 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 2 minutes

During SMTA Atlanta, I spoke with Albert Gaines of HiGain Design. We discussed Albert’s belief that everything starts with design and that too many engineers and designers focus solely on the final board at the expense of the documentation, which is a designer’s most important product. Do you consider your documentation to be a critical product?
Andy Shaughnessy: Albert, you are the founder, chief cook, and bottle-washer for HiGain Design. A minute ago, we were talking about how everything in electronics manufacturing really starts with design. You had an interesting point about some things that designers and design engineers sometimes neglect to consider early in the cycle.
Albert Gaines: I’ve been doing board layout since ’81, and I came through the drafting side of it. Documentation was our product. I think most engineers today lose the concept of the fact that the final product is not the prototype. They finally have it working, but they think they’re through. But their product is documentation—the Gerber package, ODB++ package, testability, assembly drawings, and all of the firmware. That documentation and traceability of that documentation is their product—not what’s sitting in the test lab.
Shaughnessy: How did we get to this point? I’m sure that there are people who have been doing this for 30 years and have never looked at the documentation as their final product.
Gaines: A lot has changed over the years because we’ve had a shift to where more EEs are doing more board layout, and we don’t have documentation departments in companies. Everybody is running freelance in their own cubicles. Nobody is enforcing what the documentation has to be. Ultimately, you end up with a board shop or an assembly house with a big void, wondering, “Am I going to get this data, the IPC-356 netlist, or the bare testing of the board? Or am I going to get an ODB++ for pick-and-place? What am I going to get? Do we have to recreate it after the fact?”
Shaughnessy: We always joke about how the designers get blamed for everything, but this sounds like one of the things that designers need to be aware of; it’s more about the documentation than anything else.
Gaines: Yes. It would be very good for each designer to have a checklist beside their desk when they’re getting ready to finish a product, detailing what they need to do—not just generate Gerbers and NC drill files and send it over the fence to a board shop. When I output documentation, I have folders for assembly data, bare board data, and testing data, and everything goes in each particular folder. If something’s for assembly, you grab the whole folder, which has anything that may deal with the assembly world or test world or bare board. It’s good to have that reminder. Another resource is your magazines. You’ve published information on what average documentation looks like, but I wonder how many designers look at that list and say, “What is that?” They don’t even know what it is.
To read this entire interview, which appeared in the June 2019 issue of Design007 Magazine, click here.
Suggested Items
Microchip Enters into Partnership Agreement with Delta Electronics on Silicon Carbide Solutions
07/18/2025 | Globe NewswireThe growth of artificial intelligence (AI) and the electrification of everything are driving an ever-increasing demand for higher levels of power efficiency and reliability.
ESD Alliance Reports Electronic System Design Industry Posts $5.1 Billion in Revenue in Q1 2025
07/16/2025 | SEMIElectronic System Design (ESD) industry revenue increased 12.8% to $5,098.3 million in the first quarter of 2025 from the $4,521.6 million registered in the first quarter of 2024, the ESD Alliance, a SEMI Technology Community, announced in its latest Electronic Design Market Data (EDMD) report.
Beyond Design: Refining Design Constraints
07/17/2025 | Barry Olney -- Column: Beyond DesignBefore starting any project, it is crucial to develop a thorough plan that encompasses all essential requirements. This ensures that the final product not only aligns with the design concept but is also manufacturable, reliable, and meets performance expectations. High-speed PCB design requires us to not only push technological boundaries but also consider various factors related to higher frequencies, faster transition times, and increased bandwidths during the design process.
Prague PEDC: Call for Abstracts Deadline July 31
07/16/2025 | Pan-European Electronics Design Conference (PEDC)The second Pan-European Electronics Design Conference (PEDC) will take place Jan. 21-22, 2026, in Prague, Czech Republic. The call for abstracts deadline is July 31. Organized jointly by the German Electronics Design and Manufacturing Association (FED) and the Global Electronics Association PEDC serves as a European platform for knowledge exchange, networking, and innovation in electronics design and development.
The Pulse: Design Constraints for the Next Generation
07/17/2025 | Martyn Gaudion -- Column: The PulseIn Europe, where engineering careers were once seen as unpopular and lacking street credibility, we have been witnessing a turnaround in the past few years. The industry is now welcoming a new cohort of designers and engineers as people are showing a newfound interest in the profession.