The Shaughnessy Report: Zee Plane! Zee Plane!
Target Condition: Distribution of Power—Denounce the Ounce
Fresh PCB Concepts: Resilience and Renewal in Domestic PCB Manufacturing
Advanced Packaging Means Advanced Routing Issues
January 26, 2023 | Kris Moyer, IPCEstimated reading time: 1 minute
In today’s ever-shrinking world of electronics designs, the use of BGA parts with very fine pitch features is becoming more prevalent. As these fine-pitch BGAs continue to increase in complexity and user I/O (number of balls), the difficulty of finding escape routes and fan-out patterns increases. Additionally, with the shrinking of silicon geometry leading to both smaller channel length and increased signal integrity issues, some of the traditional BGA escape routing techniques will require a revisit and/or adjustment to allow for not only successful fan-out, but also successful functioning of the circuitry of the BGA design.
Historically, BGAs could be routed using traditional full through-via structures, with dog-bone traces off the BGA pad. These BGAs were typically 1.27 mm in pitch and had sufficient clearance between the pads to place a Class 3 Level A via without violating any design rules. Additionally, the feature sizes of these packages were sufficient to fabricate in 1-ounce copper without any issues. With increases in chip complexity and I/O density, most BGA packages are now 1 mm or smaller pitch, with some packages as small as 0.4 mm pitch. With these finer pitch packages, it is no longer possible to use traditional full-thru via structures under the BGA. This, in turn, will require the use of sequential lamination and micro-via structures in order to successfully escape route the BGA. Figure 1 shows a comparison between the package and feature sizes of 484-ball 1 mm pitch BGA (U100) and a 100-ball 0.4 mm pitch BGA (U101).
First, we look at the 1 mm pitch part, then evaluate what it will take to escape all balls to the outside perimeter of the BGA. For this evaluation, we will only consider the use of stacked microvias. Staggered microvias will also work, but require significantly more board area. Additionally, the stackup will assume dual stripline for all internal signal layers.
To read this entire article, which appeared in the January 2023 issue of Design007 Magazine, click here.
Share on:
Testimonial
"Our marketing partnership with I-Connect007 is already delivering. Just a day after our press release went live, we received a direct inquiry about our updated products!"
Rachael Temple - AlltematedSuggested Items
Alpha Insights, Performance by Design: Understanding Heat at the Core of Every Design
11/11/2025 | Team Alpha -- Column: Alpha Insights: Performance by DesignPower isn’t just about current. It’s about control. As electronic systems grow smaller and faster, every amp and every layer generates a new source of heat. That heat is more than a byproduct. It’s a measure of efficiency, a benchmark of performance, and often the first indication of failure.
The Shaughnessy Report: Zee Plane! Zee Plane!
11/11/2025 | Andy Shaughnessy -- Column: The Shaughnessy ReportPlanes aren’t magic, but they are big time-savers. Without planes, designers would have to create thousands of traces to accomplish the same objectives. You can imagine the first time a designer thought about using a sheet of copper, asking, “Hey, why am I killing myself laying out all these traces? Can’t I just use this sheet of copper instead?”
November 2025 Design007 Magazine: Proper Plane Design
11/10/2025 | I-Connect007 Editorial TeamWithout planes, designers would have to create thousands of traces to accomplish the same objectives. Power planes provide low impedance and stable power to every component on the board, much like a large power bus. Ground planes stabilize reference voltage, improve thermal performance, and help preclude EMI issues. Power and ground plane design is often a battle of tradeoffs.
Trouble in Your Tank: Understanding Interconnect Defects, Part 1
11/04/2025 | Michael Carano -- Column: Trouble in Your TankThis month, I’ll address interconnect defects (ICDs). While this defect continues to rear its ugly head, don’t despair. There are solutions, most of which center on process control and understanding the relationship of the chemistry, materials, and equipment. First, though, let’s discuss ICDs.
Target Condition: Distribution of Power—Denounce the Ounce
11/05/2025 | Kelly Dack -- Column: Target ConditionHave you ever wondered why the PCB design segment uses ounces to describe copper thickness? There’s a story behind all of this—a story that’s old, dusty, and more than a little absurd. (Note that I didn’t add “Like many of us.”) Legend has it that back in the days of copper tinkers and roofing tradesmen, the standard was set when a craftsman hammered out a sheet of copper until it weighed one ounce, when its area conveniently matched the square of the king’s foot.