Illinois Researcher Receives DARPA Contract to Design a Hybrid Robot
June 7, 2016 | University of Illinois at Urbana-ChampaignEstimated reading time: 3 minutes
Illinois researcher Hae-Won Park has been awarded a Robotics Fast Track contract from the Defense Advanced Research Projects Agency (DARPA) to design a hybrid robot that can glide, land, and walk.
His ground-breaking design connects two widely researched robot forms – UAVs and quadruped robots – and is inspired by the flying squirrel, or Glaucomys volans. This animal can glide between trees and walk on branches to harvest food and escape from predators.
Park’s robot would be dropped from an aerial vehicle, glide like a flying squirrel, then land and continue walking on a variety of terrains, with proposed applications in reconnaissance missions, military scouting, and disaster response efforts, particularly in difficult-to-access or hazardous environments.
Other robots that can walk or fly and that are used in these situations, are often met with a number of challenges, such as limited battery life, constrained mobility in tight spaces, and an inability to travel long distances.
Park’s flying squirrel will address these flaws. The combined mobility of walking and flying will give the bots the large range of coverage of existing flying robots as well as the long-lasting operational hours of a ground vehicle. Additionally, the ability to gather information about environmental conditions is crucial to saving lives. Thus, they can be used independently or in swarms to share environmental awareness via a mobile sensor network.
While there have been other robots of a similar design, most research has focused on very small robots that could not complete the missions Park believes his robot can accomplish. These smaller bots also tend not to boast complex combinations between walking and gliding, and as a result, they cannot walk well and their wings lack active control.
Park, an assistant professor in the Department of Mechanical Science and Engineering at the University of Illinois at Urbana-Champaign, got the idea for the flying squirrel model while watching a National Geographic Channel documentary called “Super Squirrel” that depicts the animal jumping and gliding between trees to navigate the woods.
“Their aerodynamic maneuvers are so elegant, dynamic, and efficient,” Park said. “They use their limbs and tails, changing the shape of the wing to steer and control the gliding. That’s where I got my inspiration.”
His design includes development of soft silicone wing structures that will attached to the robot’s limbs and allow it to glide. They will feature adjustable stiffness and morphing abilities, and will serve as a shape-morphing aerodynamic control surface when stretched.
“An ideal material would be both compliant and strong, such that the wing can be stretched to increase the aerodynamically active surface area when gliding and be furled to not obstruct while walking,” Park said.
This is part of what he calls a multifunctional body frame, i.e. one that has the physical structure to allow the bot to walk and glide.
The body frame will be 3D-printed with lightweight materials – allowing for fast prototyping – like carbon fiber composite material, engineered plastics, and compliant resins. Other parts will be off-the-shelf components, lowering the cost enough to make the robots expendable after use. The entire bot is estimated to weigh only about 1.5 pounds.
Park directs the Dynamic Robotics Lab at Illinois. He earned a PhD in mechanical engineering from the University of Michigan in 2012, a master’s degree in mechanical engineering in 2007 from Yonsei University, and a bachelor’s degree, also in mechanical engineering, from Yonsei University in 2005. After holding positions as a Postdoctoral Associate and a Research Scientist at MIT, he joined the MechSE Department at Illinois in September 2015.
DARPA is an agency of the U.S. Department of Defense responsible for the development of emerging technologies for use by the military.
Suggested Items
Cadence, TSMC Collaborate on Wide-Ranging Innovations to Transform System and Semiconductor Design
04/25/2024 | Cadence Design SystemsCadence Design Systems, Inc. and TSMC have extended their longstanding collaboration by announcing a broad range of innovative technology advancements to accelerate design, including developments ranging from 3D-IC and advanced process nodes to design IP and photonics.
Ansys, TSMC Enable a Multiphysics Platform for Optics and Photonics, Addressing Needs of AI, HPC Silicon Systems
04/25/2024 | PRNewswireAnsys announced a collaboration with TSMC on multiphysics software for TSMC's Compact Universal Photonic Engines (COUPE). COUPE is a cutting-edge Silicon Photonics (SiPh) integration system and Co-Packaged Optics platform that mitigates coupling loss while significantly accelerating chip-to-chip and machine-to-machine communication.
Siemens’ Breakthrough Veloce CS Transforms Emulation and Prototyping with Three Novel Products
04/24/2024 | Siemens Digital Industries SoftwareSiemens Digital Industries Software launched the Veloce™ CS hardware-assisted verification and validation system. In a first for the EDA (Electronic Design Automation) industry, Veloce CS incorporates hardware emulation, enterprise prototyping and software prototyping and is built on two highly advanced integrated circuits (ICs) – Siemens’ new, purpose-built Crystal accelerator chip for emulation and the AMD Versal™ Premium VP1902 FPGA adaptive SoC (System-on-a-chip) for enterprise and software prototyping.
Listen Up! The Intricacies of PCB Drilling Detailed in New Podcast Episode
04/25/2024 | I-Connect007In episode 5 of the podcast series, On the Line With: Designing for Reality, Nolan Johnson and Matt Stevenson continue down the manufacturing process, this time focusing on the post-lamination drilling process for PCBs. Matt and Nolan delve into the intricacies of the PCB drilling process, highlighting the importance of hole quality, drill parameters, and design optimization to ensure smooth manufacturing. The conversation covers topics such as drill bit sizes, aspect ratios, vias, challenges in drilling, and ways to enhance efficiency in the drilling department.
Elevating PCB Design Engineering With IPC Programs
04/24/2024 | Cory Blaylock, IPCIn a monumental stride for the electronics manufacturing industry, IPC has successfully championed the recognition of the PCB Design Engineer as an official occupation by the U.S. Department of Labor (DOL). This pivotal achievement not only underscores the critical role of PCB design engineers within the technology landscape, but also marks the beginning of a transformative journey toward nurturing a robust, skilled workforce ready to propel our industry into the future.
Copyright © 2024 I-Connect007 | IPC Publishing Group Inc. All rights reserved.
Log in