Dan’s Biz Bookshelf: ‘Costovation: Innovation That Gives Your Customers Exactly What They Want—And Nothing More’
The Right Approach: ‘Twas the Night Before Christmas (Harley-style)
It’s Only Common Sense: Dear Santa, Here’s My Sales Wish List
Inkjet Solder Resists for Digital Manufacturing: Elpejet
November 29, 2019 | Lackwerke Peters GmbH & Co. KGEstimated reading time: 1 minute
The application of fine structures within a reliable process is enabled by the inkjet technology, a digital print method. Eliminating the process steps of pre-drying, exposure and development, steps which are essential in the processing of similar high resolution photoimageable solder resists, this method of inkjet application brings a tremendous potential for savings. Thanks to the direct digital realisation of layouts, it is possible to flexibly and rapidly modify the layouts; even small and very small series can be implemented in a cost-effective manner.
One of the technical benefits of inkjet printing is the fact that different layer thicknesses can be applied on one PCB side, thus permitting a high edge coverage along with low layer thicknesses in critical areas. Vias and other areas, if necessary, can be directly saved out from the printing process to avoid the risk of defects as they may be generated by incomplete curing or the free development of photoimageable inks.
Nevertheless, the developer is faced with particular challenges as far as the formulation of high functional inkjet inks is concerned, since the basic prerequisites such as a very low viscosity and small particle size, distinctly reduce the range of suitable raw materials.
Special requirements are also imposed by the print method as such. The printer and, what is more, an appropriate print head must be chosen carefully, in view of fulfilling the specific demands in terms of resolution and process speed. Special skills are needed by the operator to develop suitable print strategies for perfect coating results, as well as for the coating process as such.
Peters’ latest Elpejet formulations reach good properties for the solder resists: With the respective print head adjusted, they provide an outstanding print image and an edge coverage precise to specification, along with a high resolution. Among the typical application parameters, there is pinning with UV LEDs immediately after printing, an additional UV bump if necessary, or thermal curing to achieve relevant final properties such as “no bleeding,” adhesion, scratch/crack resistance etc.
The Elpejet solder resists were tested with various print heads such as the KM 1024i by Konica Minolta or the Dimatrix Samba G3L by Fuji Film, which are both drop-on-demand systems (DoD) using the piezo technology. The R&D department is still working on the final fine tuning. Visit www.peters.de.
Share on:
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 5
12/23/2024 | I-Connect007 Editorial TeamChapter 5 introduces the advantages of using low-temperature soldering for through-hole components, including cost efficiency, reliability improvement, and reduced warpage. Also covered: the evaluation of different fluxes and the performance of HRL3 in wave soldering and selective soldering processes.
Overview of Soldering Systems With Vacuum
12/18/2024 | Dr. Paul Wild, Rehm Thermal Systems GmbHWhen soldering electronic assemblies, the focus of the vacuum application is on the removal of volatile substances from the solder joints and the associated reduction of pore formation. Particularly in the thermal management of power electronics components, pores can cause so-called hotspots with higher temperatures due to their poor heat conduction. These hotspots can lead to overheating of the components on the one hand and to thermally induced destruction of the solder structure on the other.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
12/13/2024 | Andy Shaughnessy, I-Connect007This week, Peter Tranitz discusses the upcoming Pan-European Electronics Design Conference, set for Jan. 29-30 in Vienna, Austria. Pete Starkey brings us a review of the most recent EIPC Technical Snapshot webinar, which featured a global PCB maker update by Dr. Hayao Nakahara. Don't miss our interview with Manfred Huschka, who explains how companies can begin their own China Plus One plan. Stan Farnsworth breaks down photonic soldering and discusses its use in soldering materials that are not typically compatible. I also enjoyed Dan Beaulieu’s discussion on the value of consistency, and why just showing up for work is half the battle, especially in an inconsistent, evolving industry like ours.
Advancing Photonic Soldering
12/11/2024 | Nolan Johnson, SMT007 MagazineStan Farnsworth, director of customer satisfaction at PulseForge, discusses the advancements in photonic soldering that highlight its energy efficiency and versatility. Over the past two years, the company has refined its applications for flexible substrates and energy reduction, finding that photonic soldering allows the processing of materials that typically aren’t thermally compatible and offers significant energy savings compared to traditional methods.
Indium Introduces New ROL0 and Halogen-free Flux-cored Wire
12/11/2024 | Indium CorporationIndium Corporation announced the global availability of CW-807RS, a new high-reliability, halide- and halogen-free flux-cored wire that improves wetting speeds and cycle times for electronics assembly and robot soldering applications.