DELO: New Semicon Adhesive Propels Autonomous Driving Forward
October 20, 2023 | DELOEstimated reading time: 1 minute
DELO has developed a flexible electronics adhesive that permanently seals sensor housings airtight and thus reliably protects components such as image sensors. DELO DUALBOND BS3770 meets the stringent requirements of the semiconductor and automotive industries and helps drive innovation in autonomous driving.
The autonomous driving trend comes with ever-stricter safety requirements. Therefore, reliable components such as image sensors are installed in LiDAR and RADAR systems. Sensor housings on PCBs must be hermetically sealed throughout their entire service life in order to maintain their function permanently without interruption. However, previous solutions for hermetically sealing the housing and filter glass are reaching their limits due to these stricter requirements, failing to withstand the tests of the automotive industry, according to standard AEC-Q100.
DELO has developed DELO DUALBOND BS3770, a special electronics adhesive for semiconductor manufacturers to meet the demanding reliability and qualification tests of automotive suppliers.
Unlike adhesives previously available on the market, the newly developed adhesive is a flexible product with a Young's modulus of less than 5 MPa at room temperature. Due to its flexible properties starting from a temperature as low as approximately -50 °C, the adhesive can compensate for pressure changes that occur, such as those caused by temperature changes, humidity differences, or heat input in the reflow process during production. As a result, defects such as pop-ups or delamination do not occur, and the sensor is permanently protected.
DELO DUALBOND BS3770 can be precisely applied by needle dispensing while maintaining narrow and high bondlines. Curing takes place in two consecutive steps using UV light and heat. After dispensing, the adhesive is fixed in a few seconds by means of classic light fixation. Alternatively, it can be transferred to the B-stage, which is particularly relevant for bonding filter glasses with blackprint. At this stage, it achieves an initial adhesion comparable to tape. Afterwards, the second component can be joined. Thanks to the adhesive’s initial adhesion, the component is directly fixed so that it can be entirely processed further. Final curing takes place in a convection oven at +150 °C within 40 minutes.
In addition to image sensors for LiDAR and RADAR applications, DELO DUALBOND BS3770 is also used in driver monitoring and for 5G applications.
Suggested Items
Ansys’ Collaboration with Schrödinger will Accelerate Materials Development with Unprecedented Multiscale Simulation
05/09/2024 | ANSYSAnsys and Schrödinger are collaborating to deliver an ICME approach that bridges the gap between materials discovery and product development.
American Standard Circuits to Exhibit at Focus on PCB 2024 Italy
05/09/2024 | American Standard CircuitsAmerican Standard Circuits will be exhibiting at this year’s Focus on PCB Italy 2024 to be held on May 15 and 16 at the Vicenza Expo Centre, Vicenza, Italy.
Sondrel Awarded New Video Processor ASIC Design and Supply Contract
05/09/2024 | SondrelSondrel, a leading provider of ultra-complex custom chips for leading global technology brands, is pleased to announce that it has won a major ASIC design and supply contract for a next generation, video processing chip.
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
Real Time with… IPC APEX EXPO 2024: ASMPT and Technica's Successful Partnership and Future Plans
05/08/2024 | Real Time with...IPC APEX EXPONolan Johnson speaks with Frank Medina and Jeff Timms about the fruitful collaboration between ASMPT and Technica and the upcoming launch of a machine with enhanced capabilities. They also discuss partnerships with semiconductor firms, customer demo plans, and the significance of the demo center. The conversation highlights the potential in North America.