Going Carbon Free Boosts Battery Life
February 10, 2017 | A*STAREstimated reading time: 2 minutes
Zinc-air batteries are one of the most promising solutions for the large-scale storage of intermittently-generated renewable electricity from solar, wind or tidal: they are non-flammable, inexpensive and with a very high energy density.
Oxygen (red) and water (red and blue) molecules react on the carbon-free electrocatalyst surface (gray) as the metal-air battery is charged.
But the lifetime of current zinc-air devices is far too short to be commercially viable, because oxygen attacks and corrodes their carbon-based components. Researchers at A*STAR have now developed a carbon-free version of one of the battery’s key components, the oxygen electrocatalyst1.
Conventional rechargeable batteries store all electrochemically active materials within the device. Metal-air batteries however use oxygen from the surrounding air as the active cathode material, significantly boosting the battery’s storage capacity. To incorporate oxygen into the battery’s electrochemical cycle, these batteries use an oxygen electrocatalyst, which requires good electrical conductivity for fast electron transfer. Various metals and other catalytic materials have been tried as the electrocatalyst, but virtually all have to be laced with carbon to raise their electrical conductivity. Over time, the carbon corrodes, eventually leading to device failure.
Yun Zong and Zhaolin Liu from the Institute of Materials Research and Engineering (IMRE) at A*STAR and their colleagues have now developed a highly active oxygen electrocatalyst that contains no carbon.
This material — nickel-doped lanthanum strontium manganite (LSMN) — is a member of the perovskite family, a recently discovered group of electrochemically active materials that are also causing a stir as potential solar panel materials. “The high intrinsic electrical conductivity of LSMN means that carbon is not needed as additive for conductivity enhancement,” Zong says.
By alternating the ratio of nickel to manganese in the material, Zong was able to tune the perovskite’s performance. The best-performing formulation, containing 10 per cent nickel, matched the electrocatalytic performance of palladium on carbon, the current benchmark electrocatalyst. Yet, without the carbon, the stability of the material was greatly enhanced. The team tested LSMN over 300 electrochemical cycles and saw negligible performance degradation.
The next hurdle to overcome, Zong explains, is changing the process. In current metal-air battery designs, the catalyst is formed layer by layer on to a mat of carbon. “This defeats the purpose of using carbon-free catalysts, as underlying carbon may still suffer corrosion,” Zong says. One possibility is to replace the carbon mats with a nickel foam, on to which the carbon-free electrocatalyst could be grown in situ, he adds. “Our group is developing metal-air batteries where all components are essentially carbon-free.”
The team is also working on carbon-free versions of other battery technologies, says Zong.
Suggested Items
Material Insight: The Dielectric Constant of PCB Materials
05/17/2024 | Dr. Preeya Kuray -- Column: Material InsightIn the world of PCB design, miniaturization can be achieved by using low dielectric constant (Dk) materials. Low Dk materials can allow for a reduction in thickness while maintaining a given trace width, leading to lower transmission loss and higher density circuitry.
IPC APEX EXPO: Some Thoughts About Growth
05/16/2024 | Dan Feinberg, I-Connect007After two and a half days of wandering the aisles at IPC APEX EXPO 2024, for the first time, I almost felt like I was exploring CES. There were so many booths and exhibits that I could describe, but I’d like to focus on the growth and huge value of this event, which has expanded well beyond just the growing and impressive exhibit show floor.
The Shaughnessy Report: Unlock Your High-speed Material Constraints
05/15/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportThe world of PCB materials used to be a fairly simple one. It was divided into two groups: the “traditional” laminates, often called FR-4, and the high-speed laminates developed especially for high-speed PCBs. These were two worlds that usually didn’t collide. But then traditional laminates started getting better, and high-speed designers and design engineers took notice and started to reconsider what FR-4 could be used for.
Breaking High-speed Material Constraints: Design007 Magazine — May 2024
05/14/2024 | I-Connect007 Editorial TeamDo you need specialty materials for your high-speed designs? Maybe not. Improvements in resins mean designers of high-speed boards can sometimes use traditional laminate systems instead of high-speed materials, saving time and money while streamlining the fab process. In the May 2024 issue of Design007 Magazine, our contributors explain how to avoid overconstraining your materials when working with high-speed boards.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.