-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
Understanding MIL-PRF-31032, Part 4
October 20, 2020 | Anaya Vardya, American Standard CircuitsEstimated reading time: 3 minutes
Overview
Continuing with Part 4 of the discussion on understanding the military PCB performance standard MIL-PRF-31032, the next step in the process is to create four new procedures to address the unique requirements of the military.
Qualification and Add-On Procedure
This process provides the guidelines for the initial qualification of the company, as well as a path for future add-on qualifications. The first thing that needs to be included is the process for developing the qualification test vehicle. This is the specific PCB design that will be used to build the qualification boards. The documentation required must also be identified, such as production traveler, test vehicle design, drawings, multilayer layup, etc.
Test Vehicle
A company will qualify for specific technology and will need to develop a qualification test plan, which is a document that specifies the following minimum attributes of the qualification board:
- Max. Number of Layers and Dielectric Type
- Max. Panel Size
- Max. Board Thickness
- Min. Drilled Hole Before Plating
- Aspect Ratio
- Min. Conductor Width
- Via Structure
- Min. Conductor Space
- Hole Preparation
- Hole Wall Conductive Coating
- Copper Plating
- Solder Resist
- Silkscreen
- Final Finish
- Additional Fabrication Capabilities
- Controlled Impedance
It is important to note here that the qualification “flows down” but not “up.” In other words, if an 18-layer is qualified, layer counts less than 18 layers can be built as long as the other above parameters are the same, but a 20-layer would not be allowed.
Sample Size and Data Requirements
The next section would be to establish the lot size of the qualification lot and the sample sizes that will be used for testing. The data recording and retention of all qualification records must be defined, including coupons and any extra boards left over from the qualification lot.
Failure Analysis and Resubmission
A DLA-approved third-party testing lab must be selected to use for the initial qualification as well as the ongoing monthly testing. Should a submitted sample fail any tests, this procedure needs to have a provision for failure analysis and corrective action. This typically leverages the existing processes already in place. The rules for resubmitting new qualification boards must also be defined here, particularly that additional extra samples from the failed lot cannot be used.
Qualification Test Summary and Reporting
This section outlines the components for the summary that is needed to be submitted to the DLA after all tests and inspections have been successfully performed, including the third-party lab). This includes things like the travelers, internal and external test and inspection results, lot conformance forms and results, failure mode for any rejections, dimensional and electrical test parameters and measurements, and a copy of the qualification test plan.
Add-On Qualification
MIL-PRF-31032 allows for the expansion of the qualified technology through the add-on qualification process. A technology that falls within 25% of the current qualified technology can be built with a new qualification test plan and TRB approval. For example, with a qualified 18-layer, a 22-layer could be qualified through the add-on process.
The same would apply to line width, hole size, etc. There is no need to wait for DLA approval in these cases; they will verify the add-on qualification data during their next regular visit/audit. Anything greater than a 25% technology change will require a new full qualification like the initial qualification.
Conclusion
This wraps up qualification and add-on procedures. Part 5 will focus on the next unique procedure needed to produce MIL-PRF-31032 PCBs.
Editor’s note: Read Part 1, Part 2, and Part 3.
Anaya Vardya is president and CEO of American Standard Circuits; co-author of The Printed Circuit Designer’s Guide to… Fundamentals of RF/Microwave PCBs and Flex and Rigid-Flex Fundamentals; and author of Thermal Management: A Fabricator's Perspective. Visit I-007eBooks.com to download these and other free, educational titles. He also co-authored “Fundamentals of PCB Technology.”
Suggested Items
Indium Experts to Present on High-Temperature, Lead-Free Solder Paste and High Reliability Liquid Metal Alloys Poster at ECTC
05/16/2024 | Indium CorporationIndium Corporation Research Associate Kyle Aserian will deliver a presentation at the 74th Electronic Components and Technology Conference (ECTC) on May 31, in Denver, Colorado.
Indium Experts to Present at Electronics in Harsh Environments SMTA Conference
05/13/2024 | Indium Corporationndium Corporation Technical Manager for Europe, Africa, and the Middle East, Karthik Vijay, will deliver a technical presentation and Indium Corporation Senior Technologist, Dr. Ronald Lasky, will deliver both a workshop and technical presentation at the Electronics in Harsh Environments SMTA Conference on May 14-16 in Copenhagen, Denmark.
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
AIM Solder Signs Shinil Fl Ltd. as New Distributor for Korea
05/08/2024 | AIM SolderAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce a new distribution partnership with Shinil Fl Ltd., a prominent supplier of technological solutions in the SMT and semiconductor sectors.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.