Dan's Biz Bookshelf: 'Move Your Bus'
Driving Innovation: Direct Imaging vs. Conventional Exposure
It’s Only Common Sense: Selling to Today's Generation of Buyers
Reducing Flux Splatter in Sensors and Camera Modules
October 30, 2020 | Jasbir Bath, Shantanu Joshi, and Noriyoshi Uchida, Koki Solder America And Koki Company LimitedEstimated reading time: 1 minute
Abstract
With the increased use of electronics in new technology areas, flux formulations are being developed to address the new and existing requirements. For sensors and camera modules used for Advanced Driver Assistance System (ADAS) and internet of things (IoT) applications, there is a demand for no-clean flux formulations in lead-free solder paste, which can reduce flux splattering during reflow.
Development was done on a specially adopted flux chemistry, which helped to reduce solder/flux spattering without the use of a specially developed reflow profile adjustment in an air reflow atmosphere. The flux chemistry in the Sn3Ag0.5Cu solder paste was developed so that the flux residue layer can cover the molten solder surface during reflow preventing splattering.
Tests were done on a copper plate printed with solder paste and a copper plate placed slightly above the reflowing solder paste on the test vehicle to measure flux splattering with a variety of reflow profiles evaluated. While the conventional solder pastes required an increase of the preheat temperature to drive off volatile flux components to reduce splattering, this developed paste successfully prevented the occurrence of the splatter regardless of the type of preheat and reflow profile used. The results of the work will be reported in this article.
Introduction
During surface mount assembly with solder paste, flux splattering may occur during reflow. Flux splattering occurs as flux components disperse when gas is generated, which happens when flux components contained in solder paste dissolve and volatilize and are expelled from the solder (Figure 1).
Flux spattering causes problems, such as the generation of a contact failure, which occurs when flux adheres to the contact point of connectors, as well as illuminance and recognition errors that happen when flux adheres to light-emitting diodes (LEDs), lenses, and sensor components. As a means to prevent splattered flux from adhering to components, some customers use protective tapes to reduce such flux attachment. To lessen these defects and reduce the requirement for protective tapes in these growing applications, solder pastes that do not cause the occurrence of flux splattering are increasingly needed.
This article reports on tests to determine flux splattering generation timing, conditions of the occurrence of splattering which are dependent on reflow profile, and measures to reduce flux splattering through the development of the flux in the solder paste.
To read this entire article, which appeared in the October 2020 issue of SMT007 Magazine, click here.
Share on:
Suggested Items
Driving Innovation: Direct Imaging vs. Conventional Exposure
07/01/2025 | Simon Khesin -- Column: Driving InnovationMy first camera used Kodak film. I even experimented with developing photos in the bathroom, though I usually dropped the film off at a Kodak center and received the prints two weeks later, only to discover that some images were out of focus or poorly framed. Today, every smartphone contains a high-quality camera capable of producing stunning images instantly.
Hands-On Demos Now Available for Apollo Seiko’s EF and AF Selective Soldering Lines
06/30/2025 | Apollo SeikoApollo Seiko, a leading innovator in soldering technology, is excited to spotlight its expanded lineup of EF and AF Series Selective Soldering Systems, now available for live demonstrations in its newly dedicated demo room.
Indium Corporation Expert to Present on Automotive and Industrial Solder Bonding Solutions at Global Electronics Association Workshop
06/26/2025 | IndiumIndium Corporation Principal Engineer, Advanced Materials, Andy Mackie, Ph.D., MSc, will deliver a technical presentation on innovative solder bonding solutions for automotive and industrial applications at the Global Electronics A
Fresh PCB Concepts: Assembly Challenges with Micro Components and Standard Solder Mask Practices
06/26/2025 | Team NCAB -- Column: Fresh PCB ConceptsMicro components have redefined what is possible in PCB design. With package sizes like 01005 and 0201 becoming more common in high-density layouts, designers are now expected to pack more performance into smaller spaces than ever before. While these advancements support miniaturization and functionality, they introduce new assembly challenges, particularly with traditional solder mask and legend application processes.
Knocking Down the Bone Pile: Tin Whisker Mitigation in Aerospace Applications, Part 3
06/25/2025 | Nash Bell -- Column: Knocking Down the Bone PileTin whiskers are slender, hair-like metallic growths that can develop on the surface of tin-plated electronic components. Typically measuring a few micrometers in diameter and growing several millimeters in length, they form through an electrochemical process influenced by environmental factors such as temperature variations, mechanical or compressive stress, and the aging of solder alloys.