EIPC Summer Conference 2022: Day 2 Review
June 29, 2022 | Pete Starkey, I-Connect007Estimated reading time: 11 minutes
Dr. Marko Pudas senior engineer and project manager with Picosun in Finland, discussed the technique of atomic layer deposition as a method of applying thin barrier films to PCB assemblies, which had been the subject of a successful project funded by the European Space Agency for mitigating tin whiskering.
Pudas described the principle of atomic layer deposition (ALD) as two or more chemical vapours or gaseous precursors reacting sequentially on the substrate surface, producing a solid thin film. The process cycle comprised the introduction of molecules containing element A, the adsorption of the molecules on the surface, the introduction of molecules containing element B and reaction with element A on the surface, and the completion of one monolayer of compound AB. The cycle was repeated until the desired film thickness was reached.
ALD was a batch-coating vacuum deposition process that had been shown to cover the most demanding 3D structures, down to pore sizes of less than 100 nanometres. It was capable of depositing a wide range of materials; aluminium oxide and titanium dioxide were named as examples, and was extremely repeatable in thickness and quality. Adhesion was chemical and the coating would not peel off. Typical coating thicknesses were in the range of 100 nanometres to 0.5 microns.
Pudas showed several examples illustrating the benefits of ALD in space applications, not only tin whisker mitigation, but corrosion protection, oxidation protection, even coating the insides of gas containers to prevent leakage. In high-reliability electronics it enabled very effective conformal coating of PCB assemblies, and he referenced many performance and qualification test results.
An iNEMI project comparing various test environments for conformal coating evaluation had demonstrated the effectiveness of ALD coatings on silver and copper in extremely corrosive environments. And ALD had been proposed as an alternative to polymer solder mask in critical applications.
Session 5, focused on manufacturing technologies for 5G and beyond, was moderated by Stig Källman from Ericsson.
Dr. Sebastien Depaifve, technical service engineer with Circuit Foil, discussed developments toward the next generation of ultra-flat ED-copper foils for high speed digital and radio frequency applications. He described the progression of improvements in hyper-very-low-profile foils over the last decade to the ultra-low-profile foils of the present day, explaining that in high frequency applications the signal is carried mainly on the edges of the conductor, and surface roughness contributes to significant signal loss.
He reviewed the factors influencing insertion loss: the type and content of silane bonding treatments, the metallic content of nodular or nodule-free foil treatments, the size and shape of nodules if present, the roughness on both side of the base foil and the grain size of the copper.
The electrodeposition process had been progressively improved, with optimisation of the drum surface preparation and the use of specific organic levellers. Grain-refining additives had been used to optimise grain size to one micron, which gave maximum electrical conductivity, and a model had been developed by Circuit Foil to study the influence of nodular treatment shapes on insertion loss. Lower profile copper foil resulted in lower transmission loss, especially at high frequencies, and a metallic-free passivation process had been developed.
With the decrease in roughness, it was necessary to compensate for loss of mechanical adhesion by silane or other chemical adhesion promoters, and it had been confirmed that silane content had no significant influence on insertion loss.
Depaifve concluded by reiterating that optimisation of all the different parameters was required for next generation materials development, and that the optimisation must be conducted in co-development with resin and glass suppliers.
In a logical follow-on to Depaifve’s paper, Jim Francey, Isola Group’s RF business development director in Europe, presented an update on reliability and loss properties of copper foil for 5G applications on behalf of the iNEMI 5G Copper Foil Project. The iNEMI team set out to characterise various copper surface treatments with the objective of mitigating signal loss while still maintaining good adhesion and, hence, durability of the PCB. In addition, the team undertook a comparative study to determine signal loss from copper roughening by oxide-alternative chemical bonding treatments during PCB fabrication.
Traditional measurement methods for copper adhesion such as peel strength were not always indicative of the durability and reliability of printed circuits, and contact profilometry was inadequate for ultra-low-profile copper foils. Noncontact 3-D tools as defined in IPC TM 650 2.2.22, such as white light interferometry and laser scanning microscopy gave more accurate 3D height profiles.
Certain reliability issues associated with ultra-low-profile copper foils had been identified, particularly copper-to-dielectric delamination either on the clad laminate or oxide-alternative side, or dielectric-to-dielectric where prepreg was bonded to an etched laminate surface. This interface was also a site for possible bond-line CAF growth.
The iNEMI project would benefit the industry by formulating a compendium of material performance criteria and cross referencing to a suite of existing standards, enabling users to specify a category of material that would meet electrical performance and reliability requirements whilst minimising excessive costs through over specification. Additional cost and time savings might also be realised by reducing the need for design reiteration and requalification to meet OEM specifications.
Completion of the project would enable commonality in specifying the topology of copper foil and bonding treatments, and provide better assurance for meeting PCB electrical performance characteristics. It would also provide predictability of durability and reliability of copper foil adhesion with respect to signal loss for various copper surface finishes, as well as reducing product qualification costs and associated timescales.Page 2 of 3
Testimonial
"Our marketing partnership with I-Connect007 is already delivering. Just a day after our press release went live, we received a direct inquiry about our updated products!"
Rachael Temple - AlltematedSuggested Items
Indium Corporation Promotes Two Leaders in EMEA (Europe, Middle East, and Africa) Markets
08/05/2025 | Indium CorporationWith its commitment to innovation and growth through employee development, Indium Corporation today announced the promotions of Andy Seager to Associate Director, Continental Sales (EMEA), and Karthik Vijay to Senior Technical Manager (EMEA). These advancements reflect their contributions to the company’s continued innovative efforts with customers across Europe, the Middle East, and Africa (EMEA).
MacDermid Alpha Electronics Solutions Unveils Unified Global Website to Deepen Customer, Talent, and Stakeholder Engagement
07/31/2025 | MacDermid Alpha Electronics SolutionsMacDermid Alpha Electronics Solutions, the electronics business of Elements Solutions Inc, today launched macdermidalpha.com - a unified global website built to deepen digital engagement. The launch marks a significant milestone in the business’ ongoing commitment to delivering more meaningful, interactive, and impactful experiences for its customers, talent, and stakeholders worldwide.
KOKI to Showcase Analytical Services and New HF1200 Solder Paste at SMTA Guadalajara 2025
07/31/2025 | KOKIKOKI, a global leader in advanced soldering materials and process optimization services, will exhibit at the SMTA Guadalajara Expo & Tech Forum, taking place September 17 & 18, 2025 at Expo Guadalajara, Salón Jalisco Halls D & E in Guadalajara, Mexico.
Weller Tools Supports Future Talent with Exclusive Donation to SMTA Michigan Student Soldering Competition
07/23/2025 | Weller ToolsWeller Tools, the industry leader in hand soldering solutions, is proud to announce its support of the upcoming SMTA Michigan Expo & Tech Forum by donating a limited-edition 80th Anniversary Black Soldering Set to the event’s student soldering competition.
Koh Young Appoints Tom Hattori as President of Koh Young Japan
07/21/2025 | Koh YoungKoh Young Technology, the global leader in True 3D measurement-based inspection solutions, announced the appointment of Tom Hattori as President of Koh Young Japan (JKY).