Dan’s Biz Bookshelf: ‘Abundance: How We Build a Better Future’
Trouble in Your Tank: In Complex Systems, Design Rules Aren’t Optional
It’s Only Common Sense: The Phone Is Still Your Competitive Advantage
IPC Releases “J” Revisions to Two Leading Standards for Electronics Assembly
April 8, 2024 | IPCEstimated reading time: 1 minute
IPC announces the release of revisions for two leading standards for the electronics assembly industry. IPC J-STD-001J, Requirements for Soldered Electrical and Electronic Assemblies is recognized as the sole industry-consensus standard for soldering processes and materials. IPC-A-610J, Acceptability of Electronic Assemblies, is a post-assembly acceptance standard used to ensure electronic assemblies meet acceptance requirements for the electronics industry. These two documents are often used together for the manufacture of electronic assemblies.
Revisions to these standards are completed every three years, with significant changes made to each one. Clear guidance on the use of the standard can be found in the first chapter of each document. Committee leaders addressed more than 1,350 comments for revision “J.” Some of the significant changes found in the standards are as follows:
Global changes implemented in both documents:
- Removed redundant minimum electrical clearance references – covered in Chapter 1 of documents
- Clarified the use and definition of wire, lead and conductor
Changes to IPC J-STD-001J (Representatives from 27 countries worked on the standard):
- Added hardware installation requirements
- Added graphics to address bubbles in X-ray images
Changes to IPC-A-610J (Representatives from 29 countries worked on the standard):
- Chapter 10 has new images
- Conformal coating – clarified voiding/bubbles
In addition to the new revisions for IPC J-STD-001J and IPC-A-610J, redline documents are also available. A white paper is available IPC-WP-028, Guidance on Objective Evidence for Validating the Acceptability of Bubbles in Conformal Coatings.
Share on:
Testimonial
"Our marketing partnership with I-Connect007 is already delivering. Just a day after our press release went live, we received a direct inquiry about our updated products!"
Rachael Temple - AlltematedSuggested Items
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
05/08/2026 | Marcy LaRont, I-Connect007This week, I’ve selected some outstanding interviews that you’ll want to take note of. First, is a roundtable discussion featuring three dynamic industry cybersecurity experts. Please watch this important discussion that affects us all. Following that, I spotlight the IPC-2581 Consortium, which explains why IPC-2581 is the standard to replace Gerber data for manufacturing. Next, I am including my interview with PCBAA and AAM, who collaborated to release a short documentary on U.S. PCB manufacturing.
Global Electronics Association to Testify at the Office of the U.S. Trade Representative Panel on Section 301 Structural Excess Capacity
05/08/2026 | Global Electronics AssociationChris Mitchell, Vice President for Global Government Relations at the Global Electronics Association, will testify before the Office of the U.S. Trade Representative (USTR) Panel on Section 301 Structural Excess Capacity on Friday, May 8.
Hall of Fame Spotlight Series: Highlighting Karen McConnell
05/07/2026 | Dan Feinberg, I-Connect007In 2021, Karen McConnell was awarded the Raymond E. Pritchard Hall of Fame award in recognition of her contributions to the Association and the electronics industry. As a senior staff member and CAD/CAM engineer at Northrop Grumman Enterprise Services, her primary responsibility was to develop a common, shared EDM (Electronic Document Management) library to support the electrical and PCB design tool initiatives across Northrop Grumman Mission Systems.
A Necessary Shift From Gerber to IPC-2581
05/07/2026 | Tracy Riggan, Global Electronics AssociationIPC-2581 is an open, vendor-neutral data exchange standard developed by the Global Electronics Association to streamline the exchange of PCB design information across fabrication, assembly, and test. It replaces multiple legacy formats—including industry standards, Gerber, and ODB++—with a single, comprehensive, XML-based dataset that captures all manufacturing details.
TTC-LLC and TTCI: Smarter Training, Stronger Test at PCB East 2026
04/27/2026 | The Test Connection Inc.The Training Connection LLC (TTC-LLC) and The Test Connection, Inc. (TTCI) will be exhibiting together at PCB East 2026, taking place April 28–May 1 at the DCU Convention Center in Worcester, Massachusetts. Attendees can find both teams at Booth #103 during the main exhibition day on Wednesday, April 29.