Partial HDI: A Complete Solution
October 10, 2024 | I-Connect007 Editorial TeamEstimated reading time: 3 minutes
We recently spoke with IPC instructor Kris Moyer about partial HDI, a process that’s recently been growing in popularity. Partial HDI allows designers to escape route out from tight-pitch BGAs on one layer, where a mechanically drilled plated through-hole is not an option, while avoiding the complexity and expense of sequential lamination cycles.
As Kris explains, this process doesn’t add much to the cost, and it’s fairly straightforward. But there are some competing signal integrity and fabrication requirements to contend with. We asked Kris to walk us through this process.
Andy Shaughnessy: We’ve been talking recently about partial HDI. You’ve been teaching this in your IPC classes. Tell us about it.
Kris Moyer: The BGAs are the most problematic as far as tight pitch, along with the column grid array (CGA), and the land grid array (LGA). All these packages have been going to smaller pitches. When they first came out, we were at 1.27 mm pitch, and you could easily get a mechanically drilled plated through-hole via between the lands. But as you start getting below that pitch to 0.5 mm, 0.4 mm, and smaller, you are not able to place a mechanically drilled plated through-hole in there and still meet the IPC design and producibility requirements. You also need to go to very thin coppers to etch the feature geometries that small. We call this partial HDI, but many companies call it hybrid construction. Fortunately, we can now implement some HDI technology in one lamination cycle without going through full sequential lamination, which is a big advantage.
Shaughnessy: I imagine that there are some trade-offs when we mix technologies like this.
Moyer: Yes. The problem is, it's not just that the pitch is smaller; the size of the land is also smaller, so the spacing between the lands is smaller. In traditional boards, we know how to work with half-ounce copper, or 1-ounce copper. But now we're in quarter-ounce, eighth-ounce, 20-micron, 15-micron, or 5-micron copper thicknesses to get the etching that fine. With a 0.5 millimeter pitch BGA, we're talking about 3 or maybe 2 mils of copper-to-copper between the lands.
You can't etch that out of traditional 1-ounce copper. With these hybrid designs, you can build up all the inner layers with standard 1-ounce copper, but on the outer layer where these BGAs are being attached, you will have to go to very thin coppers and doing some laser-drill microvia technology to get a via feature sufficiently small enough that gets between the pads to get down to that first layer from the solder pads.
Marcy LaRont: You don’t have to do 2-4-2 buildup boards? Is that what we're talking about here?
Moyer: That’s right. The 2-4-2 is full HDI with sequential lamination. The number 4 in 2-4-2 means that you build four layers using standard multilayer fabrication. Then on each of the two sides, the top and the bottom, you add two HDI layers sequentially. With partial HDI, we only need one HDI layer on that one surface. You can build it in one lamination cycle because you only have to laser drill that first outermost layer. But you will need a thin layer to meet the aspect ratio requirements of microvias. You might not necessarily have a reinforcement layer. That's one of the issues that we have with HDI. Often, to get those very thin dielectrics—the 1-mil dielectric layers that we do with HDI layers—we're basically doing resin-coated coppers without any reinforcement material.
To continue reading this article, which appeared in the October 2024 issue of Design007 Magazine, click here.
Suggested Items
UHDI Fundamentals: ‘UHDI’ Bleeding-edge Entertainment Applications, Part 1
10/10/2024 | Anaya Vardya, American Standard CircuitsAs soon as we cross below the 1-mil (0.001") line width threshold, we need to stop talking in terms of mils and ounces and begin talking in terms of microns. For reference, a 3-mil trace is 75 microns, so a 1-mil trace is 25 microns. In general terms, ultra high density interconnect refers to line and spaces on a printed circuit board that are sub-25 micron. In the context of this article, ultra high-definition interconnect (UHDI) refers to the technology and infrastructure used to transmit and connect ultra high-definition signals, typically 4K, 8K, or even higher resolutions, across devices like displays, cameras, servers, and processors.
The Shaughnessy Report: Are You Partial to Partial HDI?
10/08/2024 | Andy Shaughnessy -- Column: The Shaughnessy ReportSometimes, a little technology is all you need. Star Trek’s Borg character only needs a funky eyepiece contraption to access all The Collective’s data, like an outer space Wi-Fi. Like the Borg’s eyepiece, we may only need a little bit of HDI in one corner of the board. We might only need partial HDI.
October Issue of Design007 Magazine: Partial HDI
10/08/2024 | I-Connect007 Editorial TeamOur expert contributors provide a complete, detailed view of partial HDI this month. Most experienced PCB designers can start using this approach right away, but you need to know these tips, tricks and techniques first.
Introducing the Ultra HDI Learning Pavilion at SMTA International 2024
10/07/2024 | SMTAThe SMTA is thrilled to announce the launch of the Ultra HDI (UHDI) Learning Pavilion, a first-of-its-kind experience dedicated to advancing Ultra-High Density Interconnect technology.
Cost-optimize Your PCB Design and Specifications
08/20/2024 | Erik Pedersen and Richard Koensgen, ICAPE GroupKnowledge is the key to identifying the small details that makes the big cost difference for your printed circuit board. There are many types of printed circuit boards and multiple choices between the development of schematic and BOM to PCB technology selection, electronic PCB design, mechanical and physical properties, and PCB specification.