American Made Advocacy: Rebuilding America’s Military Stockpiles Begins With Microelectronics
The Right Approach: The End of an Era—DoD Proposes MIL-PRF-31032 Cancellation
Defense Speak Interpreted: Hypersonics Report Back After Six Years of Silence
BOOK EXCERPT: The Printed Circuit Designer’s Guide to... DFM Essentials, Chapter 2
November 14, 2024 | I-Connect007 Editorial TeamEstimated reading time: 2 minutes
The Printed Circuit Designer’s Guide to... DFM Essentials
by Anaya Vardya, American Standard Circuits / ASC Sunstone Circuits
Chapter 2: Panelization
Panelization is the process of placing one or more PCBs on a manufacturing panel and incorporating features to assist manufacturing (such as tooling holes, fiducials, coupons, panel thieving, etc.). Panelization is one of the highest impact factors in the cost of a PCB.
The panel area available for circuit boards plus coupons is known as the usable area (Figure 2.1). Test coupons are added by the fabricator to the perimeter of the manufacturing panel outside the usable area. The number and type of coupons are based on the specs that the PCBs are being built to and requirements for controlled impedance. Coupons may sometimes further reduce the amount of a PCB panel that is available for the circuit boards. This is defined by the fabricator as required perimeter for coupons. This is typically about 1 inch or 25.4 mm and is a fixed area based on panel size. Panel utilization is measured as a percentage, defined by the total area for PCBs divided by the total panel area.
Cost-effective material utilization is defined by a target panel with greater than 75% panel utilization. Raw laminate is one of the primary cost constituents of a multilayer PCB. Optimizing panel structures around standard base materials while achieving maximum material utilization on one of the standard panel sizes can have a significant impact on multilayer board prices and deliveries. The three most preferred sizes in North America are 12x18 inches, 18x24 inches and 21x24 inches, with 18x24 inches being the most common. For special applications, other panel sizes can be provided. In Asia, typically the shops will process custom panel sizes in order to maximize utilization. The most effective cost per unit area processed is usually found with a larger panel size.
Visit the I-Connect007 library to continue reading The Printed Circuit Designer’s Guide to DFM Essentials.
Share on:
Testimonial
"Your magazines are a great platform for people to exchange knowledge. Thank you for the work that you do."
Simon Khesin - Schmoll MaschinenSuggested Items
SEMI ESD Alliance 2026 Outlook: Agentic AI to Transform Chip Design and Verification
05/01/2026 | SEMIThe Electronic System Design Alliance (ESD Alliance), a SEMI Technology Community, announced its annual Executive Outlook event for semiconductor EDA, agentic AI and IP company executives.
SCHMID Launches 'Any Layer ET' for Panel-Level Advances Packaging, to Present at ECTC 2026
04/30/2026 | SCHMID GroupSCHMID Group, a global leader in advanced manufacturing solutions for the electronics and semiconductor industries, is advancing next-generation substrate manufacturing with its proprietary Any Layer ET (Embedded Trace) Process for full panel-level Advanced Packaging.
Horizon Sales Adds LPKF Laser and Electronics to Its Lineup
04/21/2026 | Horizon SalesHorizon Sales, a leading manufacturers’ representative and distributor to the electronics industry, is pleased to announce a new partnership with LPKF Laser and Electronics, a global leader in precision laser technology
Introducing FKN Systek Depanelizer with Linear Guide Table for Small PCBs
04/20/2026 | FKN SystekSingulating small PCBs with circular blade depanelizers can be a tedious repetitive process which can easily result in board damage due to operator fatigue. Increase process quality and safety by using the FKN Systek K2010 motorized circular blade depanelizer with a support table to separate the V-Scored boards.
Future-proof Laser Depaneling for PCBs with Photonics
04/10/2026 | Real Time with... APEX EXPOBill Solari of Photonics Systems USA outlines the advantages of laser depaneling for circuit board manufacturing. We learn that this advanced technology addresses rising material costs by increasing panel yield and improving edge quality. This process provides precision, suitability for medical applications, and cost-saving benefits, including the elimination of cleaning steps. There have been significant advancements in laser depaneling, offering a competitive and efficient solution for modern electronics production.