Testing Flexible Circuits, Part 2: Raw Materials and Components
October 1, 2015 | Dave Becker, All FlexEstimated reading time: 4 minutes

In this second part of a three-part series regarding testing flexible circuits, I will cover the testing of raw materials or components. The following are the common materials that go into a non-populated flex circuit:
- Copper foil
- Dielectric substrate
- Copper/dielectric laminate
- Dielectric insulators
For each of the above, there are several variations:
- Copper foil can be in different thicknesses and can be rolled annealed (RA), electro-deposited (ED) or high ductility electro-deposited (HDED). The copper surface can also come with different treatments. The variety of treatments often impart a different color to the foil. The treatments are generally used as ways to enhance bonding in subsequent lamination cycles.
- Dielectric substrates can also come in different thicknesses and compositions. Polyimide is by far the most popular film used to produce flex circuits. One of the most widely known polyimide film is DuPont’s Kapton®. Polyester, liquid crystal polymer, and PTFE (Teflon®) are also used in some specialty applications.
- Copper/dielectric laminate constructions come in many variations, as a result of combining the different copper foils with dielectrics. They also come with different adhesives that bond them together, including several adhesiveless systems. Films commonly range between .0005” and .005” in thickness. The most frequently used film is .001” thick, but as requirements vary, so will the film thickness.
- Dielectric insulators for cover films and solder masks also come in multiple thicknesses as well as material types. This would also include printable and photoimageable solder masks, which come in both film and liquid form.
In addition to raw materials, there are many consumable process materials used in the fabrication of a flexible circuit. These would include etchant chemistries, plating solutions, plating metals, resist material, developing solutions, press films and much more. These have test requirements as well, but are not specified in applicable IPC documentation.
There are two basic reasons for tests and specifications of raw materials:
1. To assure that the final flexible circuit product will meet the end user requirements.
2. To assure consistency of properties so the material can be processed with maximum efficiency. An example of a property that may make a difference to the circuit fabricator, but not to the end user, is etch-shrink of the laminate. Laminates used for flexible circuits tend to undergo small dimensional changes while being processed. This change is acceptable provided that they are consistent from lot-to-lot (predictable) and small enough so as to not adversely affect layer-to-layer alignment in multilayer circuits.
The vast majority of raw material test requirements are specified in IPC-6013, IPC-4202, IPC-4203, and IPC-4204. There are more than 24 different tests for materials. In some cases the supplier will certify compliance to a certain specification; in other cases the supplier will provide lot test data. There are also situations where the flexible circuit manufacturer will do its own incoming testing.
The following are some of the common test requirements for materials:
- Electrical Properties
- Dielectric constant
- Surface and volume resistance
- Insulation resistance
- Mechanical Properties
- Peel strength (as received, after solder float, and after temperature cycling)
- Flexural endurance
- Low temperature flexibility
- Dimensional stability
- Solder float
- Initiation tear strength
- Propagation tear strength
- Chemical Properties
- Chemical resistance
- Fungus resistance
- Thermal Properties
- Service temperature
- Temperature cycling
- Cosmetic Properties
- Wrinkles, creases, streaks and scratches
- Inclusions
- Voids
- Holes and tears
- Pits and dents
- Other Properties
- Flammability
- Moisture absorption
- Copper foil purity
- Solderability
Other testing is done based on specific customer or industry requirements, for example out-gassing specifications are common for products that need to operate in a vacuum. The automotive industry has some special chemical resistance testing that includes brake fluids, oils and gasoline. Many customers have their own unique requirements in terms of long term temperature aging, maximum service temperature and long term moisture absorption. In general, a flexible circuit supplier will work with customers on unique test requirements and create specifications for materials that are consistent with end use requirements.
Do material properties change after going through a flexible circuit fabrication process? Or is it possible that the raw materials meet the overall requirements, but the combinations and stack-up of materials do not? The answer to both those questions is yes. For example: Two properties that materials are commonly tested for are flexibility and thermal resistance. The ductility of copper can change under heat and pressure. Sometimes platen pressing at elevated temperatures and pressures is used for dielectric bonding. If the temperature and pressure are high enough, the ductility properties can change, although for typical processing parameters, the change is very small. Sometimes a given characteristic improves, such as thermal resistance, after exposure to temperature and pressure. In most cases, the material changes through processing are known and predictable. An experienced flexible circuit manufacturer will have test data to determine where potential issues might arise.
Flex testing done on strips of foil or laminate doesn’t necessarily translate to the final product. In the case of flexibility, the etched trace patterns, surface treatments and material stack-ups can dramatically change flex properties. It is important to test properties in the stack-up and configuration of the final product, just as the customer will perform reliability testing on the finished electronic package containing the flexible circuit.
Even though the raw materials may individually meet certain specifications, it is important to determine if the final product configuration meets those specs. So testing done at the finished circuit level is also needed. Tests specific to the finished circuit will be the topic of our next column on testing.
Dave Becker is vice president of sales and marketing at All Flex Flexible Circuits LLC.
Testimonial
"We’re proud to call I-Connect007 a trusted partner. Their innovative approach and industry insight made our podcast collaboration a success by connecting us with the right audience and delivering real results."
Julia McCaffrey - NCAB GroupSuggested Items
Indium Corporation Promotes Two Leaders in EMEA (Europe, Middle East, and Africa) Markets
08/05/2025 | Indium CorporationWith its commitment to innovation and growth through employee development, Indium Corporation today announced the promotions of Andy Seager to Associate Director, Continental Sales (EMEA), and Karthik Vijay to Senior Technical Manager (EMEA). These advancements reflect their contributions to the company’s continued innovative efforts with customers across Europe, the Middle East, and Africa (EMEA).
MacDermid Alpha Electronics Solutions Unveils Unified Global Website to Deepen Customer, Talent, and Stakeholder Engagement
07/31/2025 | MacDermid Alpha Electronics SolutionsMacDermid Alpha Electronics Solutions, the electronics business of Elements Solutions Inc, today launched macdermidalpha.com - a unified global website built to deepen digital engagement. The launch marks a significant milestone in the business’ ongoing commitment to delivering more meaningful, interactive, and impactful experiences for its customers, talent, and stakeholders worldwide.
KOKI to Showcase Analytical Services and New HF1200 Solder Paste at SMTA Guadalajara 2025
07/31/2025 | KOKIKOKI, a global leader in advanced soldering materials and process optimization services, will exhibit at the SMTA Guadalajara Expo & Tech Forum, taking place September 17 & 18, 2025 at Expo Guadalajara, Salón Jalisco Halls D & E in Guadalajara, Mexico.
Weller Tools Supports Future Talent with Exclusive Donation to SMTA Michigan Student Soldering Competition
07/23/2025 | Weller ToolsWeller Tools, the industry leader in hand soldering solutions, is proud to announce its support of the upcoming SMTA Michigan Expo & Tech Forum by donating a limited-edition 80th Anniversary Black Soldering Set to the event’s student soldering competition.
Koh Young Appoints Tom Hattori as President of Koh Young Japan
07/21/2025 | Koh YoungKoh Young Technology, the global leader in True 3D measurement-based inspection solutions, announced the appointment of Tom Hattori as President of Koh Young Japan (JKY).