Testing Flexible Circuit Assemblies
January 18, 2022 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 3 minutes

I recently spoke with Bert Horner of the Test Connection Inc., about the current state of flex and rigid-flex assembly testing. He explained some of the differences between testing flex and rigid PCBs, the requirements for testing specialties such as high-voltage flex, and the added demands of handling flexible circuits.
Andy Shaughnessy: Bert, tell us about your company and the kinds of test equipment you’ve developed for flexible and rigid-flex circuits. I understand you also provide test services too; do you offer testing for flex?
Bert Horner: The Test Connection Inc., is a full services test engineering and test service that offers different test solutions to test rigid and rigid flex circuits. For prototype or lower volume assemblies, we have flying probe and boundary scan solutions and for the production testing, we have in-circuit test and functional test solutions from partners like Teradyne, Keysight, and National Instruments. TTCI works with fixture partners to offer custom in-house solutions to support and access these challenging assemblies.
Shaughnessy: What are the most common tests for flexible circuit assemblies as well as the biggest challenges? Do high-voltage flexible circuits require a different set of tests than the rest?
Horner: For flying probe testing (FPT), in-circuit testing (ICT) and functional test (FT), the biggest challenge is the tooling for testing the assembly. For the FPT, the handling of the unit under test (UUT) is one of the biggest challenges. This can still be a challenge if the assembly is thin and flimsy, so tooling could still be required. If ICT and FT are done on a fixture or bed-of-nails (BoN), we don’t want to introduce stress to the UUT, so “zero flex” fixturing with finite element analysis (FEA) and strain gauge might be needed, which also adds time and cost. In FT, we see that in high-voltage testing, the biggest challenge is making sure the equipment that will be testing assembly can handle the proper testing requirements. This is about the same set-up as a rigid board, but we haven’t seen too many applications that have this as a requirement.
Shaughnessy: What are some of the biggest differences between testing a flexible circuit and a traditional rigid PCB?
Horner: The physical handling is the biggest challenge in testing flex or rigid-flex circuitry. We often have to develop a custom carrier or handling fixture to test flex or rigid-flex assemblies to help with stability and support.
Shaughnessy: We’ve seen flex and rigid-flex explode in the last decade, and now flex can be found in many household and handheld devices. What trends are you seeing in the world of flex?
Horner: Test access is more of a challenge with accessing the test assemblies through connectors and SMT device “toes” of the solder joints with the assemblies going into two completely different directions. The wearable, handheld, and space applications are getting smaller, but the defense backplanes are in some cases getting larger.
Shaughnessy: How much of your job involves educating new customers about flex and testing?
Horner: We are not doing much with educating the customer on how they want to test flex circuitry, but rather showing them strengths and weaknesses in the test solutions they are choosing or that they have available to test their assemblies. If we are looking at multiple test and inspection tools to get the most coverage on these assemblies, the education becomes about what is best for manufacturing. We both learn preferences of tools that are available.
Shaughnessy: Is there anything else you’d like to add?
Horner: There are more similarities of testing flex circuitry and conventional rigid circuitry, the access, and the handling are where we see the challenge.
Shaughnessy: Thanks for your time, Bert.
Horner: Thank you for the opportunity, Andy.
This interview originally appeared in the January 2022 issue of Design007 Magazine.
Suggested Items
'Chill Out' with TopLine’s President Martin Hart to Discuss Cold Electronics at SPWG 2025
05/02/2025 | TopLineBraided Solder Columns can withstand the rigors of deep space cold and cryogenic environments, and represent a robust new solution to challenges facing next generation large packages in electronics assembly.
BEST Inc. Reports Record Demand for EZReball BGA Reballing Process
05/01/2025 | BEST Inc.BEST Inc., a leader in electronic component services, is pleased to announce they are experiencing record demand for their EZReball™ BGA reballing process which greatly simplifies the reballing of ball grid array (BGA) and chip scale package (CSP) devices.
Indium Wins EM Asia Innovation Award
05/01/2025 | Indium CorporationIndium Corporation, a leading materials provider for the electronics assembly market, recently earned an Electronics Manufacturing (EM) Asia Innovation Award for its new high-reliability Durafuse® HR alloy for solder paste at Productronica China in Shanghai.
Summit Interconnect Hollister Elevates PCB Prototyping with New TiTAN Direct Imaging System from Technica USA
05/01/2025 | Summit Interconnect, Inc.Summit Interconnect’s Hollister facility has recently enhanced its quick-turn PCB prototyping capabilities by installing the TiTAN PSR-H Direct Imaging (DI) system.
KOKI Expands U.S. Sales Coverage with Multiple New Representatives
04/29/2025 | KOKIKOKI, a global leader in advanced soldering materials and process optimization services, is pleased to announce the expansion of its U.S. sales network with the addition of three new manufacturers’ representative firms: Assembled Product Specialists, Diversitech Reps Inc., and Eagle Electronics.