Defense Speak Interpreted: Understanding What the Department of Defense Is, and Isn’t
American Made Advocacy: Rebuilding America’s Military Stockpiles Begins With Microelectronics
The Right Approach: The End of an Era—DoD Proposes MIL-PRF-31032 Cancellation
Revolutionizing Radar Signal Processing
November 1, 2022 | DARPAEstimated reading time: 2 minutes
Radar systems have seen many technology improvements in apertures (antennas) and associated hardware and software since the nascent operational versions in World War II. What hasn’t changed significantly over the decades, however, is that radars still use linear signal processing between the aperture and the detector. In the 1940s linear radar signal processing used vacuum tubes and analog circuits, while current radars accomplish linear signal processing digitally with microchips and software.
With the Beyond Linear Processing (BLiP) program, DARPA’s goal is to improve radar performance by applying innovative signal processing methods. BLiP will leverage high-power computer processing to explore new, non-linear and iterative signal processing techniques that could lead to lighter, smaller, and less expensive – but equally capable – radar systems. If successful, BLiP would enable the same radar performance achieved on large platforms today on much smaller sea, air, and ground platforms.
“A lot of radar improvements over the past 30 years have focused on growing the size of the aperture for greater sensitivity or increasing transmitter power,” said Frank Robey, BLiP program manager in DARPA’s Strategic Technology Office. “Those are important, but if we want to shrink aperture size by 50% and still get the same radar performance then we need to disrupt the linear signal processing paradigm. With the tremendous increases in computer processing power available today, we can take a fresh look at radar signal processing and explore iterative, leap-ahead techniques.”
BLiP will address the current immaturity of non-linear and iterative signal processing methods. Over the course of the two-year program, end-to-end radar signal processing chains will be developed, analyzed, implemented and tested – initially through non-real-time laboratory testing and culminating in real-time implementation and full-scale field testing using an operational National Weather Service radar. Key technical challenges for BLiP will be the development, understanding, and optimization of the signal processing chain, and the practical aspects of implementing BLiP algorithms using real-time, high-performance processing.
Share on:
Testimonial
"Advertising in PCB007 Magazine has been a great way to showcase our bare board testers to the right audience. The I-Connect007 team makes the process smooth and professional. We’re proud to be featured in such a trusted publication."
Klaus Koziol - atgSuggested Items
New Book Explores How UV Technology Is Transforming Electronics Protection, Efficiency, and Sustainability
05/14/2026 | I-Connect007I-Connect007 proudly announces the recent release of The Printed Circuit Designer’s Guide to…™ UV Curable Conformal Coatings. Authored by respected industry technologists Brian Chislea and Cody Schoener, PhD, of Dow, Inc., this new volume offers a comprehensive exploration of UV-curable conformal coatings and their expanding role in improving the protection, performance, and sustainability of electronic assemblies.
Rethinking Reinforcement Materials for Advanced Packaging
05/14/2026 | Ivana Ivanovic, Flexiramics B.V.Materials that once quietly supported the industry are now becoming limiting factors. The electronics industry is experiencing unprecedented pressure as RF systems push into mmWave frequencies, high-speed digital architectures advance into their next performance generation, and power densities climb across automotive, telecom, aerospace, and computing. Reinforcement materials, long treated as a background detail in laminate design, are suddenly at the centre of performance, reliability, and supply‑chain discussions.
Below the Surface: Active Component and Module Submounts—The Architecture Behind Performance
05/14/2026 | Chandra Gupta -- Column: Below the SurfaceIf you were to peel back the layers of a modern electronic system, such as a satellite transceiver, a LiDAR module, or a 5G base station, you would not immediately notice a specific component doing some of the most important work. It doesn’t amplify signals, emit light, or process data, yet without it, none of those functions would be stable, reliable, or scalable. That component is the active device submount.
Protecting Advanced Trucking Electronics in Harsh Environments
05/13/2026 | Beth Massey, MacDermid Alpha Electronics SolutionsFor decades, trucking was defined by horsepower, payload, and driver endurance. Today, the competitive edge lies in electronics, as advanced sensing, communications, and data processing systems reshape how commercial vehicles operate. The industry is rapidly digitizing, with electronic systems now critical to safety, uptime, and fleet efficiency. Technologies like ADAS, radar, lidar, and telematics enable real-time decision-making, while distributed sensors monitor key vehicle functions. Because these systems operate in harsh conditions, environmental protection using potting, coatings, and encapsulation is now a core design priority.
NEO Battery Partners with Highest-Ranking ROK Army's Capital Defense Command for Defense Drone & Robotics Batteries
05/08/2026 | PR NewswireNEO Battery Materials Ltd., a low-cost, silicon-enhanced battery developer that enables longer-running, rapid-charging batteries for drones, robotics, and physical AI, is pleased to announce it has entered into a significant defense partnership agreement with the Republic of Korea Army's Capital Defense Command.