-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Growing Industry
In this issue of PCB007 Magazine, we talk with leading economic experts, advocacy specialists in Washington, D.C., and PCB company leadership to get a well-rounded picture of what’s happening in the industry today. Don’t miss it.
The Sustainability Issue
Sustainability is one of the most widely used terms in business today, especially for electronics and manufacturing but what does it mean to you? We explore the environmental, business, and economic impacts.
The Fabricator’s Guide to IPC APEX EXPO
This issue previews many of the important events taking place at this year's show and highlights some changes and opportunities. So, buckle up. We are counting down to IPC APEX EXPO 2024.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - pcb007 Magazine
TTM Chippewa Falls Acquires 4 New Hakuto Dry film Laminators from Matrix USA
April 13, 2016 | Matrix USA Inc.Estimated reading time: 1 minute
Matrix has sold four Hakuto Mach 630NP Auto Dry Film Laminators to TTM, following a successful four-month trial.
Matrix is extremely pleased with the performance of Hakuto’s new Mach 630NP/6630NP Series Dry Film Laminators and is prepared to provide sales and service to all regions of North America.
Fred Long, Matrix Business Development, says, “The new Mach 630NP machine addresses the accuracy needed to assist in the transfer of very fine lines on the latest HSLL laminates using Super Low Profile Copper surfaces. This is made possible by the new Lamination Module with its EVEN Heat and EVEN Pressure across the entire surface of the laminated panel. In addition, the ability to change the rubber lamination rolls in seconds will not only increase productivity but will also offer alternative “quick change” rubber solutions for different product needs. The complete redesign of the film lamination approach will now begin to reach the most important users of this latest technology. Matrix is eager to show manufacturers that by using the new system, Productivity and Yield will now surpass all traditional ROI expectations.”
To watch the Real Time With...IPC interview with Dan Feinberg and Fred Long discussing the new laminating machine and its innovative features, click here.
During the next few weeks, Matrix is scheduled to place additional machines in three specific regional areas in the US. Customers will then be able to travel to these sites and see the machines in operation.
About Matrix USA Inc.
Committed to the motto, “Quality Products, Dependable People”, Matrix was established in 1977 with the objective of providing quality raw materials to the North American Printed Circuit Board Industry. Matrix has four rapid-response warehouses located throughout the US and Canada that fulfill high quality, fast delivery, and custom orders daily. For further information, click here.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.