Making a Solar Energy Conversion Breakthrough With Help From a Ferroelectrics Pioneer
August 11, 2016 | Drexel UniversityEstimated reading time: 6 minutes
Designers of solar cells may soon be setting their sights higher, as a discovery by a team of researchers has revealed a class of materials that could be better at converting sunlight into energy than those currently being used in solar arrays. Their research shows how a material can be used to extract power from a small portion of the sunlight spectrum with a conversion efficiency that is above its theoretical maximum — a value called the Shockley-Queisser limit. This finding, which could lead to more power-efficient solar cells, was seeded in a near-half-century old discovery by Russian physicist Vladimir M. Fridkin, PhD, a visiting professor of physics at Drexel University, who is also known as one of the innovators behind the photocopier.
The team, which includes scientists from Drexel University, the Shubnikov Institute of Crystallography of the Russian Academy of Sciences, the University of Pennsylvania and the U. S. Naval Research Laboratory recently published its findings in the journal Nature Photonics. Their article “Power conversion efficiency exceeding the Shockley-Queisser limit in a ferroelectric insulator,” explains how they were able to use a barium titanate crystal to convert sunlight into electric power much more efficiently than the Shockley-Queisser limit would dictate for a material that absorbs almost no light in the visible spectrum — only ultraviolet.
A phenomenon that is the foundation for the new findings was observed by Fridkin, who is one of the principal co-authors of the paper, some 47 years ago, when he discovered a physical mechanism for converting light into electrical power — one that differs from the method currently employed in solar cells. The mechanism relies on collecting “hot” electrons, those that carry additional energy in a photovoltaic material when excited by sunlight, before they lose their energy. And though it has received relatively little attention until recently, the so-called “bulk photovoltaic effect,” might now be the key to revolutionizing our use of solar energy.
The Limits of Solar Energy
Solar energy conversion has been limited thus far due to solar cell design and electrochemical characteristics inherent to the materials used to make them.
“In a conventional solar cell — made with a semiconductor — absorption of sunlight occurs at an interface between two regions, one containing an excess of negative-charge carriers, called electrons, and the other containing an excess of positive-charge carriers, called holes,” said Alessia Polemi, PhD, a research assistant professor in the Department of Materials Science and Engineering in Drexel’s College of Engineering and one of the co-authors of the paper.
In order to generate electron-hole pairs at the interface, which is necessary to have an electric current, the sunlight’s photons must excite the electrons to a level of energy that enables them to vacate the valence band and move into the conduction band — the difference in energy levels between these two bands is referred to as the “band gap.” This means that in photovoltaic materials, not all of the available solar spectrum can be converted into electrical power. And for sunlight photon energies that are higher than the band gap, the excited electrons will lose it excess energy as heat, rather than converting it to electric current. This process further reduces the amount of power can be extracted from a solar cell.
“The light-induced carriers generate a voltage, and their flow constitutes a current. Practical solar cells produce power, which is the product of current and voltage,” Polemi said. “This voltage, and therefore the power that can be obtained, is also limited by the band gap.”
But, as Fridkin discovered in 1969 — and the team validates with this research — this limitation is not universal, which means solar cells can be improved.
Page 1 of 2
Suggested Items
IDTechEx Discusses Low-Loss Materials: The Enabler of Future Connected Vehicles?
05/06/2024 | IDTechExFuture connected vehicles will offer future drivers a safer, smoother, and more convenient driving experience. Not only will drivers get access to more navigation and entertainment options, but they will also gain access to safety technologies that will potentially reduce accidents, improve congestion, and reduce emissions globally by allowing vehicle safety systems to communicate with each other and with city traffic infrastructure.
LQDX Divests Aluminum Soldering Business - Mina™ - to Taiyo America Inc.
05/02/2024 | PRNewswireLQDX, formerly known as Averatek Corp., developer of high-performance materials for advanced semiconductor manufacturing, today announced that it has divested its aluminum soldering business – known as MinaTM – to Taiyo America Inc., a global market leader in advanced electronic materials.
Indium Corporation Expert to Present on Pb-Free Solder for Die-Attach in Discrete Power Applications
04/30/2024 | Indium CorporationIndium Corporation Product Manager – Semiconductor Dean Payne will present at the Advanced Packaging for Power Electronics conference, hosted by IMAPS, held May 8-9 in Woburn, Massachusetts, USA.
Real Time with... IPC APEX EXPO 2024: Adhesive Materials and Equipment Update with Dymax
05/01/2024 | Real Time with...IPC APEX EXPOVirginia Hogan, global business development manager at Dymax, discusses adhesive materials, dispensing and curing equipment, a new, high-reliability conformal coating, and various materials and dispensing methods.
Real Time with... IPC APEX EXPO 2024: Sustainability in the Industry
04/26/2024 | Real Time with...IPC APEX EXPOGuest Editor Henry Crandall and Chris Nash of Indium Corporation discuss the company's 90th anniversary and its focus on sustainability. They focus on the benefits of sustainable materials, their compatibility, and value propositions. The conversation also highlights how Durafuse LT technology's role in reducing reflow temperatures is leading to significant cost and energy savings. Nash also touches on downstream sustainability efforts such as using recycled materials for packaging.