American Made Advocacy: Smart Policies Can Ensure AI Data Centers Are Secure
Beyond the Board: Early Engagement Means Faster Prototyping for Defense Programs
Defense Speak Interpreted: The Autonomous Plane Battle—Skyborg Vs. Loyal Wingman
October 31, 2016 EPA CDR Reporting Applies to Many Manufacturers
October 25, 2016 | IPCEstimated reading time: 1 minute
The deadline for complying with the U.S. Environmental Protection Agency (EPA) Chemical Data Reporting (CDR) rule is October 31, 2016.
Under EPA interpretation of the CDR regulations, manufacturers who send byproducts, such as wastewater treatment sludge, spent etchant or spent baths, for recycling may be required to report under the CDR because EPA views the byproduct stream as a new chemical because it is a feedstock to the recycling process. The applicability of the CDR reporting requirements depends on a number of factors including the amounts of specific chemicals in the byproduct.
For example, any printed circuit board manufacturer using ammonium chloride etchant in excess of approximately 784 gallons per year during 2102, 2013, 2014, or 2015 and sending the spent etchant for recycling is likely to exceed the 2,500 lb. reporting threshold for copper tetraammine chloride.
Recently, IPC achieved a long-sought goal with the inclusion of a requirement for EPA to reexamine this rule passage as part of the of The Frank R. Lautenberg Chemical Safety for the 21st Century Act amending TSCA, however this does not change the need to report this year.
For more information, please review our CDR guidance and TSCA CDR website. You may also contact Fern Abrams, IPC director of regulatory affairs at FernAbrams@ipc.org or +1 202 661-8092.
Share on:
Testimonial
"In a year when every marketing dollar mattered, I chose to keep I-Connect007 in our 2025 plan. Their commitment to high-quality, insightful content aligns with Koh Young’s values and helps readers navigate a changing industry. "
Brent Fischthal - Koh YoungSuggested Items
Trouble in Your Tank: Understanding Interconnect Defects, Part 1
11/04/2025 | Michael Carano -- Column: Trouble in Your TankThis month, I’ll address interconnect defects (ICDs). While this defect continues to rear its ugly head, don’t despair. There are solutions, most of which center on process control and understanding the relationship of the chemistry, materials, and equipment. First, though, let’s discuss ICDs.
WestDev Announces Advanced Thermal Analysis Integration for Pulsonix PCB Design Suite
10/29/2025 | WestDev Ltd.Pulsonix, the industry-leading PCB design software from WestDev Ltd., announced a major enhancement to its design ecosystem: a direct interface between Pulsonix and ADAM Research's TRM (Thermal Risk Management) analysis software.
Designers Notebook: Power and Ground Distribution Basics
10/29/2025 | Vern Solberg -- Column: Designer's NotebookThe principal objectives to be established during the planning stage are to define the interrelationship between all component elements and confirm that there is sufficient surface area for placement, the space needed to ensure efficient circuit interconnect, and to accommodate adequate power and ground distribution.
Episode 6 of Ultra HDI Podcast Series Explores Copper-filled Microvias in Advanced PCB Design and Fabrication
10/15/2025 | I-Connect007I-Connect007 has released Episode 6 of its acclaimed On the Line with... American Standard Circuits: Ultra High Density Interconnect (UHDI) podcast series. In this episode, “Copper Filling of Vias,” host Nolan Johnson once again welcomes John Johnson, Director of Quality and Advanced Technology at American Standard Circuits, for a deep dive into the pros and cons of copper plating microvias—from both the fabricator’s and designer’s perspectives.
Nolan’s Notes: Tariffs, Technologies, and Optimization
10/01/2025 | Nolan Johnson -- Column: Nolan's NotesLast month, SMT007 Magazine spotlighted India, and boy, did we pick a good time to do so. Tariff and trade news involving India was breaking like a storm surge. The U.S. tariffs shifted India from one of the most favorable trade agreements to the least favorable. Electronics continue to be exempt for the time being, but lest you think that we’re free and clear because we manufacture electronics, steel and aluminum are specifically called out at the 50% tariff levels.