Electrifying News...Nano-Modified Aerospace Composites
December 19, 2016 | University of BristolEstimated reading time: 1 minute
Carbon fibre composites, composed of reinforcing carbon fibres within a plastic, have revolutionised industries that demand strong, yet light materials. However, their application has been hindered by inherently poor electrical and thermal conductivities.
New research, published in the journal Scientific Reports, demonstrates that by growing nanomaterials, specifically carbon nanotubes, on the surface of the carbon fibres it is possible to impart these necessary properties.
The research, conducted at the University of Surrey’s Advanced Technology Institute (ATI) and the University of Bristol’s Advanced Composite Centre for Innovation and Science (ACCIS), shows off the potential of a carbon fibre reinforced plastic to be made multifunctional, while still maintaining its structural integrity. Novel functionality including sensors, energy harvesting lighting and communication antennae can now be integrated into the structure of the composite to usher in a new era in composite technology.
Dr Thomas Pozegic, Research Associate in ACCIS and formerly a PhD student at the University of Surrey, explained: "The aerospace industry still relies on metallic structures, in the form of a copper mesh, to provide lightning strike protection and prevent static charge accumulation on the upper surface of carbon fibre composites because of the poor electrical conductivity. This adds weight and makes fabrication with carbon fibre composites difficult. The material that we have developed utilises high-quality carbon nanotubes grown at a high density to allow electrical transport throughout the composite material."
Dr Ian Hamerton, Reader in Polymers and Composite Materials in ACCIS, commented: "The research has shown that carbon nanotubes can significantly enhance the thermal conductivity of carbon fibre composites. This will have wide-reaching benefits in the aerospace industry, from enhancing de-icing solutions to minimising the formation of fuel vapours at cruising altitudes."
Professor Ravi Silva, Director of the ATI and Head of the Nanoelectronics Centre (NEC) said: "In the future, carbon nanotube modified carbon fibre composites could lead to exciting possibilities such as energy harvesting and storage structures with self-healing capabilities. We are currently working on such prototypes and have many ideas including the incorporation of current aerospace/satellite technology in automotive design."
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.