Powered by Magnets, Energy Harvester Converts Wasted Heat Into Electricity
March 6, 2017 | Virginia TechEstimated reading time: 3 minutes
Postdoctoral researcher Jinsung Chun holds a thermo-magneto-electric generator, which uses magnets to dissipate heat from mechanical systems and turn it into useful electricity.
Researchers at Virginia Tech have built a device that uses a pair of magnets and a piezoelectric lever to convert wasted heat to useful electricity.
The system is the first working, bulk-scale example of a thermo-magneto-electric generator, a new type of thermal energy harvester designed to operate efficiently without the large temperature gradients required by most systems.
Thermal energy harvesters recover waste heat, a significant source of energy loss in homes, manufacturing plants, and vehicles. Energy seeps out of mechanical systems from hot surfaces and exhaust gases and dissipates into the environment.
“You can take any mechanical process around you, like running your lawnmower or a car, and about 40 to 60 percent of the energy you’re putting in as electricity or gas is wasted as heat. It’s a huge loss,” said Shashank Priya, the Robert E. Hord Jr. Professor of Mechanical Engineering in the College of Engineering and associate director for research and scholarship at the Institute for Critical Technology and Applied Science, who led the study. “There’s a lot of interest in capturing that heat, which now gets discarded.”
Converting some of the lost heat to electricity would lower overall fuel consumption, cutting costs and blunting environmental impacts. By siphoning off heat more quickly, it would also increase the performance of systems with electrical components, which operate more efficiently at lower temperatures.
The new thermal energy harvester, described in a study published in Scientific Reports, brokers the conversion of heat to electricity by taking advantage of materials called soft magnets, which are easily magnetized and demagnetized.
One such material is gadolinium, which is magnetic at around room temperature, but loses its magnetism as it warms up.
In Priya’s energy harvester, a gadolinium soft magnet is attached to a flexible plastic cantilever. A hard, or permanent, magnet rests against the heat source — for example, the hot surface of a computer’s CPU. Magnetic attraction pulls the two magnets together, allowing heat to flow from the hard magnet into the soft magnet. This heats the soft magnet above its transition temperature, and it becomes nonmagnetic.
Without magnetic attraction to bind it to the hard magnet, the soft magnet is pulled away by the cantilever. Separated from the heat source, the soft magnet cools down; the drop in temperature reactivates its magnetic properties, starting the process over again.
Pulled in one direction by the hard magnet, and the other by the cantilever, the soft magnet cycles up and down as it gains and loses magnetism. Meanwhile, it absorbs heat from the hot surface via the hard magnet, cooling it and dispersing the thermal energy into the environment, which acts as a heat sink.
But the energy contained in the heat is recycled, because the piezoelectric cantilever converts the soft magnet’s up-and-down motion into electricity that can be used or stored.
One of the key advantages of the device is that it effectively harvests thermal energy from heat sources not dramatically hotter than the ambient air — the kind most common in homes and industrial plants.
“If you look around, you see mostly low-temperature gradients,” Priya said. “But at low temperatures, there aren’t many promising solutions.”
In tests, the researchers used their device to harvest thermal energy from heat sources around 70 to 80 degrees Celsius. The device operating temperature is mainly governed by the heat required to demagnetize the soft magnet; with currently available materials, it can be as low as 50 to 60 degrees Celsius.
The new energy harvester’s ability to operate at moderate temperatures — along with its compact size and mechanical simplicity — could make it practical for household use. Priya envisions that the heat emanating from everyday appliances could be used to power networks of sensors in data-driven “smart” homes.
“There are a lot of places where even a watt of electricity is sufficient, if you want to run a sensor node,” Priya said. “Let’s say you want to monitor some process, like measure a temperature or a fluid flow or pressure change. All you need is a burst of thermal energy available to you in a periodic manner.”
The researchers are scaling up the thermal energy harvester to increase its electrical output, refining the materials and design, and adapting it for specific applications.
The study’s first author is Jinsung Chun, a postdoctoral researcher in the Department of Mechanical Engineering. First-year doctoral student Ravi Kilgore, who holds a Doctoral Scholars Fellowship from the Institute for Critical Technology and Applied Science, and other graduate students in the department of mechanical engineering also worked on the project.
Suggested Items
PCB Market Size to Grow by $29.06B from 2024-2028
05/17/2024 | PRNewswireThe global printed circuit board (PCB) market size is estimated to grow by USD 29.06 bn from 2024-2028, according to Technavio. The market is estimated to grow at a CAGR of over 6.6% during the forecast period.
epoxySet Launches EC-1015HP - High Temperature, Crack Resistant Epoxy Potting
05/13/2024 | epoxySetepoxySet introduces the EC-1015HP epoxy potting compound. This heat cure system is designed for temperature cycling from -55 to 180°C with significantly better crack resistance than traditional rigid epoxies. As a low viscosity encapsulant, it is used for large and small potting applications with fragile components.
New Book on Low-temperature Soldering Now Available
04/17/2024 | I-Connect007I-Connect007 is pleased to announce that The Printed Circuit Assembler’s Guide to… Low-temperature Soldering, Vol. 2, by subject matter experts at MacDermid Alpha Electronics Solutions, is now available for download.
The Chemical Connection: Reducing Etch System Water Usage, Part 1
04/05/2024 | Don Ball -- Column: The Chemical ConnectionWater conservation has become an important component of the overall system design for most manufacturing operations today. Changing climate conditions and increasing populations are beginning to strain the freshwater supplies in many areas of the country. As a result, as equipment suppliers, we see an increasing number of requests for options that reduce water usage in proposed wet processing systems. Etching systems tend to use more water because of the need for close temperature control to maintain steady etch rates and the rinsing requirements for complete removal of corrosive etchants from the surface of the product before the next process step. This column contains some simple suggestions for reducing water usage in etch systems that won’t strain the budget too much.
Indium’s Sze Pei Lim to Present on Semiconductor Packaging at ICEP Japan
04/02/2024 | Indium CorporationIndium Corporation’s Senior Global Product Manager for Semiconductor and Advanced Materials, Sze Pei Lim, is scheduled to present at the International Conference on Electronics Packaging (ICEP 2024).