Study Opens Route to Ultra-Low-Power Microchips
November 13, 2018 | MITEstimated reading time: 6 minutes
A new approach to controlling magnetism in a microchip could open the doors to memory, computing, and sensing devices that consume drastically less power than existing versions. The approach could also overcome some of the inherent physical limitations that have been slowing progress in this area until now.
Image Caption: Illustration shows how hydrogen ions (red dots), controlled by an electric voltage, migrate through an intermediate material to change the magnetic properties of an adjacent magnetic layer(shown in green).
Researchers at MIT and at Brookhaven National Laboratory have demonstrated that they can control the magnetic properties of a thin-film material simply by applying a small voltage. Changes in magnetic orientation made in this way remain in their new state without the need for any ongoing power, unlike today’s standard memory chips, the team has found.
The new finding is being reported today in the journal Nature Materials, in a paper by Geoffrey Beach, a professor of materials science and engineering and co-director of the MIT Materials Research Laboratory; graduate student Aik Jun Tan; and eight others at MIT and Brookhaven.
Spin Doctors
As silicon microchips draw closer to fundamental physical limits that could cap their ability to continue increasing their capabilities while decreasing their power consumption, researchers have been exploring a variety of new technologies that might get around these limits. One of the promising alternatives is an approach called spintronics, which makes use of a property of electrons called spin, instead of their electrical charge.
Because spintronic devices can retain their magnetic properties without the need for constant power, which silicon memory chips require, they need far less power to operate. They also generate far less heat — another major limiting factor for today’s devices.
But spintronic technology suffers from its own limitations. One of the biggest missing ingredients has been a way to easily and rapidly control the magnetic properties of a material electrically, by applying a voltage. Many research groups around the world have been pursuing that challenge.
Previous attempts have relied on electron accumulation at the interface between a metallic magnet and an insulator, using a device structure similar to a capacitor. The electrical charge can change the magnetic properties of the material, but only by a very small amount, making it impractical for use in real devices. There have also been attempts at using ions instead of electrons to change magnetic properties. For instance, oxygen ions have been used to oxidize a thin layer of magnetic material, causing a extremely large changes in magnetic properties. However, the insertion and removal of oxygen ions causes the material to swell and shrink, causing mechanical damage that limits the process to just a few repetitions — rendering it essentially useless for computational devices.
The new finding demonstrates a way around that, by using hydrogen ions instead of the much larger oxygen ions used in previous attempts. Since the hydrogen ions can zip in and out very easily, the new system is much faster and provides other significant advantages, the researchers say.
Because the hydrogen ions are so much smaller, they can enter and exit from the crystalline structure of the spintronic device, changing its magnetic orientation each time, without damaging the material. In fact, the team has now demonstrated that the process produces no degradation of the material after more than 2,000 cycles. And, unlike oxygen ions, hydrogen can easily pass through metal layers, which allows the team to control properties of layers deep in a device that couldn’t be controlled in any other way.
“When you pump hydrogen toward the magnet, the magnetization rotates,” Tan says. “You can actually toggle the direction of the magnetization by 90 degrees by applying a voltage — and it’s fully reversible.” Since the orientation of the poles of the magnet is what is used to store information, this means it is possible to easily write and erase data “bits” in spintronic devices using this effect.
Page 1 of 2
Suggested Items
Rogers Announces Further Actions to Streamline Operations and Drive Margin Improvement
06/07/2024 | Rogers CorporationRogers Corporation announced plans to drive further operational efficiency and margin improvement. Rogers intends to wind down manufacturing of advanced circuit materials and other related activities at its Evergem, Belgium factory by mid-2025.
The Pulse: Overconstraining: Short, Slim, and Smooth
06/06/2024 | Martyn Gaudion -- Column: The PulseEngineering is both an art and a science. The design engineer’s task is (almost) always to bring product to market that meets specifications at the best and most economical price suited to the appropriate end use requirements. From a PCB perspective, designers are faced with a bewildering and almost overwhelming choice of materials at their disposal.
Overconstrain? Underconstrain? Selecting Materials for High-speed Designs
06/06/2024 | Andy Shaughnessy, Design007 MagazineWhen selecting materials for a high-speed design, you need to be very familiar with the materials’ electrical characteristics, as well as the requirements of the PCB you’re designing. There are myriad details that need to be considered during the material selection process, and missing one iota can lead to your job being put on hold. We asked Stephen Chavez, principal technical product marketing manager at Siemens, to share his thoughts on material selection for high-speed designs. Steph discusses material constraints, stackups, and the cut-off point when a “traditional” laminate will (and won’t) work for a high-speed board.
DuPont’s Randal King Joins Purdue University’s Semiconductor Degrees Leadership Board
06/06/2024 | DuPontDuPont announced that Randal King, PhD, Vice President of R&D/Technology, DuPont Electronics & Industrial, has been named to Purdue University’s Semiconductor Degrees Leadership Board.
IPC Releases Newest List of Standards Updates, Revisions
06/03/2024 | IPCEach quarter, IPC releases a list of standards that are new or have been updated. To view a complete list of newly published standards and standards revisions, translations, proposed standards for ballot, final drafts for industry review, working drafts, and project approvals, visit ipc.org/status. These are the latest releases for Q2.