Ledia 6 Direct Imaging System Offers Enhanced Speed and Precision
December 29, 2019 | Pete Starkey, I-Connect007Estimated reading time: 3 minutes
I recently met with Ucamco’s Michel Van den heuvel, imaging product group director, to discuss the benefits of the Ledia 6 direct imaging system, which was introduced earlier this summer and features scan-alignment and improvements in registration and positioning accuracy.
Pete Starkey: Michel, it’s great to see you again.
Michel Van den heuvel: Hi, Pete. I’m happy to see you.
Starkey: One of your specialties is the Ledia direct imaging system, and I understand that there have been some new developments lately. Can you bring us up-to-date with the latest advances?
Van den heuvel: After Ledia 5, SCREEN Graphic and Precision Solutions introduced Ledia 6, which is a further improvement and development of the existing Ledia 5. Based on the feedback they had from customers, they have made further enhancements. One of the main improvements is a new camera-registration system. On the existing Ledia 5, they used step-alignment, which means that the table stops, switches on the light of the registration camera, and takes a picture of the fiducial, and then the table moves to the next fiducial and takes a picture again.
In the Ledia 6, they have introduced scan-alignment. The table moves at a constant speed and does not stop any more. When it needs to take a fiducial, it switches on the light and quickly takes the picture—it’s like a stroboscope effect—and switches the light on and off while the table keeps moving. Through software, they stitch all these pictures together and know exactly where all the fiducials are. It goes much faster because the table doesn’t need to stop.
Starkey: How accurately can you hold registration with this system?
Van den heuvel: Registration and positioning accuracy go together because, eventually, the result that the customer can see on the panel is positioning accuracy. With Ledia 6, we have improved positioning accuracy by 10% compared to the Ledia 5, and also improved registration accuracy by 20%.
In addition to the scan-alignment system, the width of the registration cameras has been doubled in size. Take the example where a solder mask panel has been routed after the panel has been made. This can influence not only the exact size but also the position of the fiducials towards the edge of the panel. With a smaller camera, this could previously result in sometimes missing a fiducial. The double-width scan-alignment camera will completely resolve this issue.
Another improvement, together with the scan-alignment, is that if you have multiple step-and-repeat single PCBs on the panel, and the fiducials of adjacent PCBs are within 12 millimeters of each other, our front-end software will automatically combine these fiducials and scan them with one camera in one go. Instead of doing two scans, you can combine it in one scan. Especially for step-and-repeats of panels, such as BGAs, this greatly improves scan-alignment time.
A further improvement involves new, stronger light sources that we built into the imaging heads. We made a change to the optics to make them capable of handling this stronger light source, which results in up to 25–30% throughput improvement. And the less sensitive is the material, the bigger the improvement you will notice.
Starkey: In a typical case with a solder mask, what would be the exposure time?
Van den heuvel: Exposing time depends on the panel. For 100 millijoules, the exposing time for a 610 x 457-millimeter [24 x 18-inch] panel side would be around 23.7 seconds compared to the previous 30.3 seconds, including four-point registration. Whenever you gain 6.6 seconds in a single run, that is a huge improvement.
Starkey: And your light sources can be tuned to achieve the optimum wavelength for the photo-initiator system in the solder mask?
Van den heuvel: Yes. The way the optical heads are designed, we can 100% independently adjust the different main wavelengths that we use: 365, 385, and 405 nanometers. We can independently adjust each wavelength from zero to 100% and tune to the solder mask at hand and achieve the best possible sidewall, reducing undercut to a minimum.
Starkey: Have you already launched the Ledia 6 into the market?
Van den heuvel: Yes, we have. The first systems in Europe have been sold this year, and two of them have already been installed at ICS in Italy and Optiprint in Switzerland. The results have been as we expected, and our clients are delighted with the outcome. Next week, we will install a third one at Eurocircuits in Hungary.
Starkey: That is splendid! I wish you every success with the system. Thank you very much for your time.
Van den heuvel: Thank you, Pete.
Suggested Items
Some Fundamentals of Tin-Bismuth Metallurgy and Electromigration
09/24/2024 | Prabjit Singh, Raiyo Aspandiar, Haley Fu, and L. A. SwaminathanNear-eutectic tin-bismuth alloy is a strong contender as the solder of choice for low-temperature electronic assembly applications. This article will describe the recent significant developments by the iNEMI project team on the understanding of the electromigration behavior of Sn-Bi solder which has a unique physical metallurgy and electromigration behavior quite different for that of Sn-Ag-Cu (SAC) solder and other solders in common use today.
SMTA Carolinas Chapter Hosts Expert-Led Webinar: “Mastering Solder Paste Printing for Optimal SMT Assembly”
09/24/2024 | Koh YoungThe SMTA Carolinas Chapter invites you to attend an informative webinar on "Mastering Solder Paste Printing for Optimal SMT Assembly" on Tuesday, October 15, 2024, from 12:00 PM to 1:00 PM (Eastern).
Winners of IPC Hand Soldering and Rework Competition Vietnam 2024 Announced
09/19/2024 | IPCIn conjunction with NEPCON Vietnam 2024, IPC hosted its popular IPC Hand Soldering and Rework Competition in Hanoi, Vietnam, September 11-13. Thirty-nine competitors from 16 electronics companies and one university in Vietnam vied for top honors.
Understanding Cleaning Challenges for Automated Solder Paste Dispensing
09/18/2024 | Debbie Carboni, KYZENIn today’s rapidly evolving electronics manufacturing landscape, staying abreast of innovative technologies is crucial. As solder paste and substrate materials continually evolve and become more complex, optimizing production methods with the latest technology ensures performance and quality while reducing operational costs.
Successful Rehm Technology Days 2024 – Where the Future Meets Technology
09/17/2024 | Rehm Thermal SystemsTraditionally, the Rehm Technology Days offer a valuable opportunity for knowledge exchange, networking and discussion. Once again this year, numerous customers, partner companies, press representatives and employees from the worldwide locations met at the company headquarters in Blaubeuren-Seissen.