The Knowledge Base: A Conference for Cleaning and Coating of Mission-critical Electronics
Defense Speak Interpreted: Is DARPA Still Around After CHIPS?
Beyond the Board: Orbital High Ground—Why Space Superiority Is Slipping Away
Ventec Launches High-Speed Material Option Cladded with Thin-Film Resistor Foil
September 24, 2020 | Ventec International GroupEstimated reading time: 2 minutes
For enhanced high-speed signal-handling performance required by the world's most demanding high-frequency Printed Circuit Board applications, Ventec International Group has launched a laminate option to its tec-speed 20.0 glass-reinforced hydrocarbon and ceramic laminate cladded with thin-film resistor material from Ticer.
Ventec's tec-speed 20.0 material, which combines unrivaled high-frequency performance (Dk 3.00-3.48 / Df 0.0027-0.0037), superior loss characteristics and highest reliability, is now available cladded with Ticer TCR© NiCr thin-film resistor foil as a service option. Essentially being inductor-free, the addition of the resistive material technology offers an enhanced material solution for some of today’s high-speed, low-loss, high-frequency applications where absolute performance and reliability are essential. These include aerospace & defense, radar, control circuits, sensor technologies, wireless communications, MEMS microphones/sensors/motors and medical diagnostic type applications.
Driven by the demand for reduction of dimensions and manufacturing costs of these types of devices, multi-layer technologies are one of the solutions that offer an increase in component packaging density. By adding the resistive foil layer in between the substrate and the copper layer, resistors can be embedded inside of PCBs after the lamination process.
Consequently, additional efficiencies the shorter distance between the embedded passives and active components achieves additional efficiencies that result in better signal transmission, less cross talk and improved electrical signal performance at high frequencies through lower loss and noise. In addition, material cost reduction, yield improvement, defect reduction and ultimately an optimized production cycle time and time to market can be achieved.
The embedded resistor foil layer material option named tec-speed 20.0 VT-870 H348 TCR is available in Hoz and 1oz thick foil with resistivity values of 25, 50 and 100 ?/sq.
“The high-speed signal-handling performance of our latest VT-870 H348 TCR material cladded with Ticers’ unique technology provides additional efficiencies for Ventec’s tec-speed 20.0 material,” noted Mark Goodwin, COO Europe & America. “It allows us to offer our customers an even greater choice of the best in high-quality, high-performance and reliable base material technology – all of course supported by our fast and efficient global delivery promise through our fully controlled global supply chain and dependable technical support.”
About Ventec International Group
Ventec International Group Co., Ltd. (6672 TT) is a world leader in the production of polyimide & high reliability epoxy laminates and prepregs and specialist provider of thermal management and IMS solutions. Further information about Ventec’s solutions and the company’s wide variety of products is available at www.venteclaminates.com and/or by downloading the Ventec APP.
Share on:
Suggested Items
Happy’s Tech Talk #40: Factors in PTH Reliability—Hole Voids
07/09/2025 | Happy Holden -- Column: Happy’s Tech TalkWhen we consider via reliability, the major contributing factors are typically processing deviations. These can be subtle and not always visible. One particularly insightful column was by Mike Carano, “Causes of Plating Voids, Pre-electroless Copper,” where he outlined some of the possible causes of hole defects for both plated through-hole (PTH) and blind vias.
Trouble in Your Tank: Can You Drill the Perfect Hole?
07/07/2025 | Michael Carano -- Column: Trouble in Your TankIn the movie “Friday Night Lights,” the head football coach (played by Billy Bob Thornton) addresses his high school football team on a hot day in August in West Texas. He asks his players one question: “Can you be perfect?” That is an interesting question, in football and the printed circuit board fabrication world, where being perfect is somewhat elusive. When it comes to mechanical drilling and via formation, can you drill the perfect hole time after time?
The Evolution of Picosecond Laser Drilling
06/19/2025 | Marcy LaRont, PCB007 MagazineIs it hard to imagine a single laser pulse reduced not only from nanoseconds to picoseconds in its pulse duration, but even to femtoseconds? Well, buckle up because it seems we are there. In this interview, Dr. Stefan Rung, technical director of laser machines at Schmoll Maschinen GmbH, traces the technology trajectory of the laser drill from the CO2 laser to cutting-edge picosecond and hybrid laser drilling systems, highlighting the benefits and limitations of each method, and demonstrating how laser innovations are shaping the future of PCB fabrication.
Day 2: More Cutting-edge Insights at the EIPC Summer Conference
06/18/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) summer conference took place this year in Edinburgh, Scotland, June 3-4. This is the third of three articles on the conference. The other two cover Day 1’s sessions and the opening keynote speech. Below is a recap of the second day’s sessions.
Day 1: Cutting Edge Insights at the EIPC Summer Conference
06/17/2025 | Pete Starkey, I-Connect007The European Institute for the PCB Community (EIPC) Summer Conference took place this year in Edinburgh, Scotland, June 3-4. This is the second of three articles on the conference. The other two cover the keynote speeches and Day 2 of the technical conference. Below is a recap of the first day’s sessions.