Tracking Quantum Phenomena in 2D Graphene
January 21, 2022 | Indian Institute of ScienceEstimated reading time: 2 minutes
In recent years, a phenomenon called the quantum Hall effect has emerged as a platform for hosting exotic features called quasiparticles, with properties that could lead to exciting applications in areas like quantum computing. When a strong magnetic field is applied to a 2D material or gas, the electrons at the interface – unlike the ones within the bulk – are free to move along the edges in what are called edge modes or channels – somewhat similar to highway lanes. This edge movement, which is the essence of the quantum Hall effect, can lead to many interesting properties depending on the material and conditions.
For conventional electrons, the current flows only in one direction dictated by the magnetic field (‘downstream’). However, physicists have predicted that some materials can have counter-propagating channels where some quasiparticles can also travel in the opposite (‘upstream’) direction. Although these upstream channels are of great interest to scientists because they can host a variety of new kinds of quasiparticles, they have been extremely difficult to identify because they do not carry any electrical current.
In a new study, researchers from the Indian Institute of Science (IISc) and international collaborators provide “smoking gun” evidence for the presence of upstream modes along which certain neutral quasiparticles move in two-layered graphene. To detect these modes or channels, the team used a novel method employing electrical noise – fluctuations in the output signal caused by heat dissipation.
“Though the upstream excitations are charge-neutral, they can carry heat energy and produce a noise spot along the upstream direction,” explains Anindya Das, Associate Professor in the Department of Physics and corresponding author of the study published in Nature Communications.
Quasiparticles are largely excitations that arise when elementary particles like electrons interact among each other or with matter around them. They are not truly particles but have similar particles like mass and charge. The simplest example is a ‘hole’ – a vacancy where an electron is missing in a given energy state in a semiconductor. It has an opposite charge to the electron and can move inside a material just like the electron does. Pairs of electrons and holes can also form quasiparticles which can propagate along the edge of the material.
In previous studies, the researchers have shown that it might be possible to detect emergent quasiparticles like Majorana fermions in graphene; the hope is to harness such quasiparticles to eventually build fault-tolerant quantum computers. For identifying and studying such particles, detecting upstream modes which can host them is critical. Although such upstream modes have been detected earlier in gallium-arsenide based systems, none have been identified so far in graphene and graphene-based materials, which offer much more promise when it comes to futuristic applications.
In the current study, when the researchers applied an electrical potential to the edge of two-layered graphene, they found that heat was transported only in the upstream channels and dissipated at certain “hotspots” in that direction. At these spots, the heat generated electrical noise that could be picked up by an electrical resonance circuit and spectrum analyser.
The authors also found that the movement of these quasiparticles in the upstream channels was “ballistic” – heat energy flowed from one hotspot to another without any loss – unlike the “diffusive” transport observed earlier in gallium-arsenide based systems. Such a ballistic movement is also indicative of the presence of exotic states and features that could help build energy-efficient and fault-free quantum components in the future, according to the authors.
Read the original article, here.
Suggested Items
Rules of Thumb: Design007 Magazine, November 2024
11/11/2024 | I-Connect007 Editorial TeamRules of thumb are everywhere, but there may be hundreds of rules of thumb for PCB design. They’re built on design formulas, fabricators’ limitations, and tribal knowledge. And unfortunately, some longtime rules of thumb should be avoided at all costs. How do we separate the wheat from the chaff, so to speak?
Connect the Dots: Best Practices for Prototyping
09/21/2023 | Matt Stevenson -- Column: Connect the DotsPCB prototyping is a critical juncture during an electronic device’s journey from concept to reality. Regardless of a project’s complexity, the process of transforming a design into a working board is often enlightening in terms of how a design can be improved before a PCB is ready for full production.
The Drive Toward UHDI and Substrates
09/20/2023 | I-Connect007 Editorial TeamPanasonic’s Darren Hitchcock spoke with the I-Connect007 Editorial Team on the complexities of moving toward ultra HDI manufacturing. As we learn in this conversation, the number of shifting constraints relative to traditional PCB fabrication is quite large and can sometimes conflict with each other.
Asia/Pacific AI Spending Surge to Reach a Projected $78 Billion by 2027
09/19/2023 | IDCAsia/Pacific spending on Artificial Intelligence (AI) ), including software, services, and hardware for AI-centric systems will grow to $78.4 billion in 2027, according to International Data Corporation's latest Worldwide Artificial Intelligence Spending Guide.
Intel to Sell Minority Stake in IMS Nanofabrication Business to TSMC
09/13/2023 | IntelIntel Corporation announced that it has agreed to sell an approximately 10% stake in the IMS Nanofabrication business to TSMC. TSMC’s investment values IMS at approximately $4.3 billion, consistent with the valuation of the recent stake sale to Bain Capital Special Situations.