Flexible Thinking Flexible Circuit Technology—Looking Back and Forward
Happy’s Tech Talk #29: Bend-to-Install Semi-flex FR-4
Connect the Dots: Five Best Practices for Designing Flex and Rigid-flex PCBs
Rogers to Feature Advanced Materials Technology, Capabilities for Antennas at IEEE AP-S
July 5, 2022 | Rogers CorporationEstimated reading time: 1 minute
Rogers Corporation will exhibit at the IEEE International Symposium on Antennas & Propagation (IEEE AP-S) in Denver, CO (Booth #400) on July 12-14.
The IEEE AP-S conference is intended to provide an international forum for the exchange of information on state-of-the-art research in antennas, propagation, electromagnetic engineering and radio science.
Key Rogers’ products being featured include:
Recently introduced Radix™ 3D Printable Dielectrics family of products, with the first available material featuring a dielectric constant of 2.8 and low loss characteristics at microwave frequencies. These printable dielectric materials give radio frequency (RF) designers unprecedented design freedom in creating new components, eliminating the need to consider typical manufacturing design constraints.
Radix 3D Printable Dielectrics are proprietary composite materials designed for the scalable manufacture of gradient index and controlled dk 3D structures, through a scalable, high-resolution printing process for end-use RF dielectric component manufacturing. Rogers Corporation’s first Radix 3D Printable Dielectric material has a targeted dielectric constant of 2.8 and a dissipation factor of 0.0043 at 10 GHz when cured.
MAGTREX® 555 High Impedance Laminates: The first commercially available low loss laminate with controlled and matched permeability and permittivity, enabling antenna designers to expand the trade-space of their antenna design, enabling design flexibility and optimization.
Rogers technical staff will be available to discuss the most demanding applications from Phase Array Radar Antennas, high frequency magneto-dielectric materials, ablative Radome materials, and metallized-shaped/3D ADM dielectric solutions.
Conference attendees can learn about “3D-Printed E-Band Gradient Dielectric Lens for Automotive and Industrial Applications” from Trevor Polidore of Rogers Corporation and Philip Lambert of 3DFortify at the 3D Printed Lens Antennas technical session on Friday July 15th starting at 3:20 p.m.
Share on:
Suggested Items
Würth Elektronik Now an Infineon ‘Preferred Partner’
03/13/2025 | Wurth Elektronik eiSosWürth Elektronik, one of the leading manufacturers of electronic and electromechanical components, is broadening its collaboration with semiconductor manufacturers.
Elementary Mr. Watson: Ensuring a Smooth Handoff From PCB Design to Fabrication
03/13/2025 | John Watson -- Column: Elementary, Mr. WatsonAt the 2020 Tokyo Summer Olympics, the U.S. men's 4x100-meter relay team had high hopes of winning a medal. The team comprised some of the fastest sprinters in the world, but something went wrong. In a relay, four runners must smoothly pass their baton to the next runner inside a zone on the track. If a runner drops the baton or it’s passed outside the zone, the team risks disqualification. The U.S. team’s pass between the second and third runner was messy, slowing them down. By the time the last runner received the baton, the team had lost too much time. They finished sixth in their heat and didn’t qualify for the final.
Ventec International Group Announce Launch of VT-47LT IPC4101 /126 Prepreg for HDI
03/12/2025 | Ventec International GroupVentec International Group announce launch of VT-47LT IPC4101 / 126 Prepreg. Are Microvia Failures Plaguing Your HDI Any Layer Designs? High-density interconnect (HDI) designs are pushing the envelope - higher layer count HDI relies on complex microvia designs: skip vias, staggered microvias, and stacked microvias in sequential laminations.
TI Introduces the World's Smallest MCU, Enabling Innovation in the Tiniest of Applications
03/12/2025 | PRNewswireTexas Instruments (TI) introduced the world's smallest MCU, expanding its comprehensive Arm® Cortex®-M0+ MSPM0 MCU portfolio. Measuring only 1.38mm2, about the size of a black pepper flake, the wafer chip-scale package (WCSP) for the MSPM0C1104 MCU enables designers to optimize board space in applications such as medical wearables and personal electronics, without compromising performance.
Speaking the Same Language as Your Fabricator
03/12/2025 | Andy Shaughnessy, Design007 MagazineWe do indeed have a failure to communicate; designers and fabricators often seem to be talking past each other, which can lead to jobs being put on hold. We asked Jen Kolar, VP of engineering for Monsoon Solutions, and columnist Kelly Dack to share their thoughts on ways that we can break down the communication barrier between design and fabrication. As they point out, a design kickoff checklist and a solid review process can be invaluable tools in a designer’s toolbox.