American Made Advocacy: Success in Washington Requires Patience, Persistence, and Sustained Focus
The Government Circuit: News on Defense Electronics, Europe, and Sustainability
Defense Speak Interpreted: SWaPing Nanosatellites for Defense Systems
Nihon Superior Launches Ag-free SAC305 Replacement – SN100CV
January 4, 2023 | Nihon Superior Co. LtdEstimated reading time: 2 minutes
With its rule-breaking wave solder alloy, SN100C, Nihon Superior Co., Ltd. earned global recognition as an innovator in lead-free solder formulation. The rule that SN100C broke was that you can’t make a Pb-free solder without a silver content that doubles the cost of the raw materials. Now Nihon Superior has broken that rule again with SN100CV, a reflow soldering alloy that can outperform SAC305 in reliability while being reflowable with the same thermal profile as SAC305.
The secret of the SN100CV is that it achieves its reliability and reflowability with a carefully targeted addition of cost-effective bismuth, while avoiding the susceptibility to impact loading associated with the presence of a brittle bismuth phase in the microstructure.
While the bismuth level is sufficient to bring the melting characteristics of SN100CV into a range that means it can be reflowed with the same profile as that used with SAC305, it is not so high that the limit of solid solubility is exceeded over the temperature range to which electronics assemblies are usually exposed. Therefore, performance in high strain rate loading is not compromised by the presence in the microstructure of a brittle bismuth phase.
For the creep resistance that delivers good performance in thermal cycling SAC alloys rely on the particle strengthening effect of the initially fine dispersion of closely spaced Ag3Sn particles, which acts as an obstacle to the movement of the dislocations on which deformation relies. The tin matrix in which those particles are dispersed is essentially pure tin with little resistance to the deformation that drives the fatigue cracking so that when those Ag3Sn particle coarsen and the interparticle spacing increased the resistance of the alloy to creep deformation is not much more than it would be if there were no Ag in the alloy.
By contrast the bismuth in solid solution in the tin phase of SN100CV, taking the place of some of the tin atoms in the crystal lattice, distorts the lattice planes to an extent that it creates an obstacle to dislocation movement as effective as the Ag3Sn particles in SAC alloys. The difference is that effectiveness of the bismuth as a solid solution strengthener does not change over time. The alloy is as resistant to creep deformation after 1000 hours as it was when freshly reflowed.
When combined with a completely halogen-free flux medium, P608, that can match the performance of halogen activated flux media, SN100CV delivers a cost-efficient, high yield assembly in a profile with a peak temperature under 240°C and reliability.
Share on:
Suggested Items
Book Excerpt: The Printed Circuit Assembler’s Guide to... Low-Temperature Soldering, Vol. 2, Chapter 5
12/23/2024 | I-Connect007 Editorial TeamChapter 5 introduces the advantages of using low-temperature soldering for through-hole components, including cost efficiency, reliability improvement, and reduced warpage. Also covered: the evaluation of different fluxes and the performance of HRL3 in wave soldering and selective soldering processes.
Overview of Soldering Systems With Vacuum
12/18/2024 | Dr. Paul Wild, Rehm Thermal Systems GmbHWhen soldering electronic assemblies, the focus of the vacuum application is on the removal of volatile substances from the solder joints and the associated reduction of pore formation. Particularly in the thermal management of power electronics components, pores can cause so-called hotspots with higher temperatures due to their poor heat conduction. These hotspots can lead to overheating of the components on the one hand and to thermally induced destruction of the solder structure on the other.
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
12/13/2024 | Andy Shaughnessy, I-Connect007This week, Peter Tranitz discusses the upcoming Pan-European Electronics Design Conference, set for Jan. 29-30 in Vienna, Austria. Pete Starkey brings us a review of the most recent EIPC Technical Snapshot webinar, which featured a global PCB maker update by Dr. Hayao Nakahara. Don't miss our interview with Manfred Huschka, who explains how companies can begin their own China Plus One plan. Stan Farnsworth breaks down photonic soldering and discusses its use in soldering materials that are not typically compatible. I also enjoyed Dan Beaulieu’s discussion on the value of consistency, and why just showing up for work is half the battle, especially in an inconsistent, evolving industry like ours.
Advancing Photonic Soldering
12/11/2024 | Nolan Johnson, SMT007 MagazineStan Farnsworth, director of customer satisfaction at PulseForge, discusses the advancements in photonic soldering that highlight its energy efficiency and versatility. Over the past two years, the company has refined its applications for flexible substrates and energy reduction, finding that photonic soldering allows the processing of materials that typically aren’t thermally compatible and offers significant energy savings compared to traditional methods.
Indium Introduces New ROL0 and Halogen-free Flux-cored Wire
12/11/2024 | Indium CorporationIndium Corporation announced the global availability of CW-807RS, a new high-reliability, halide- and halogen-free flux-cored wire that improves wetting speeds and cycle times for electronics assembly and robot soldering applications.