3D Laser Printing Yields High Quality Micro-Optics
April 28, 2016 | OSAEstimated reading time: 4 minutes
Researchers have demonstrated 3D printing of micron-scale optics with unprecedented performance and reproducibility. Their approach can be used to create almost any type of integrated optical element on a micron or smaller scale, which could help miniaturize instruments and devices used in applications from sensing to telecommunications.
In The Optical Society's journal for high impact research, Optica, researchers report direct fabrication of optical elements as small as 4.4 microns onto the exact center of an optical fiber only 125 microns in diameter, just slightly thicker than the diameter of a human hair. They used a technique known as femtosecond laser writing to accomplish this difficult feat and showed that the performance of the optical elements closely matched simulations.
“Although femtosecond laser writing has been demonstrated in the lab, we have shown that it can be used to make high performance micro-optics in a manner that is highly repeatable and reliable,” said Harald Giessen, chair for ultrafast nano-optics, University of Stuttgart, who led the research team. “We believe our approach can be scaled up for volume manufacturing and used to directly print almost any type of optical element on a tiny scale, opening up a new era of integrated micro- and nano-optics.”
Writing with light
Femtosecond laser writing uses a laser that emits very short pulses of light to selectively harden a light-sensitive material. The material hardens only in the small 3D area where the laser light is focused, and any unhardened material can then be washed away, revealing the 3D structure that has been created.
Although many labs around the world have made their own 3D laser writing systems, these home-made systems are sensitive to environmental conditions and variances in laser power and thus can’t reliably create high quality micro-optics. To overcome these problems, the researchers used a commercially available two-photon 3D laser lithography system designed to write nanometer-sized structures. The system, made by Nanoscribe GmbH, is engineered for stability, reliability and quality.
“We have something like a pen that we can move in 3D through a material to create structures in a manner similar to a 3D printer but at very tiny scales,” explained Giessen. “If you punch a set of parameters into our system and into a system in some other place in the world, you will get the same exact result. Even months from now, it will come out the same every time.”
Creating phase masks
The researchers used the 3D laser writing system to create optical elements known as phase masks, which offer an elegant way to shape the light coming out of the end of a fiber without using large, bulky lenses.
Normally, light leaving the end of a fiber is Gaussian, meaning that it is bright in the middle and dims towards the edges. The researchers created phase masks directly on the end of the optical fiber that shaped the light into either a flat-top profile that is equally bright across the illuminated area or a donut-shape that features an empty middle surrounded by a bright ring of light.
“Because the phase masks are so small and are created directly on the end of the optical fiber, even tiny errors in the centering of the phase mask would cause the donut-shaped beam to not look nice and round,” said Giessen. “We solved one of the hardest problems: repeatedly placing a phase mask with submicron accuracy directly in the center of the single-mode fiber.”
The direct laser writing approach can be used to create optical elements in numerous ways. The researchers found that creating phase masks ring-by-ring beginning at the center or layer-by-layer starting from the bottom, both produced high quality structures.
“Depending on how you write, you might have different optical properties, and also the velocity at which you can write and how fast you can manufacture an optical component depends strongly on your write mode,” said Timo Gissibl, University of Stuttgart, the paper’s first author.
The phase masks created by the researchers have many potential applications. By replacing large optical lenses, the top-hat phase masks could enable illumination in much smaller endoscopes, which are used to see inside the body during non-invasive surgeries or procedures such as colonoscopies. An optical fiber with the phase mask that produces donut-shaped light could be placed directly in a liquid and used for optical trapping of particles or cells, for example. Also, photoacoustic endoscopy could benefit from the very compact hollow beam delivery, says Lihong Wang, the inventor of this technology.
The research team is now conducting experiments to see if 3D laser writing can be used to create tiny phase masks that shape an optical fiber’s output into twisted light, which is of great interest for photon entanglement and other applications. “Now that the instrument is available, we are only limited by what we can think of to do with it,” said Giessen.
Suggested Items
Physicists Create Optical Component for 6G
05/20/2024 | SkoltechA joint team of physicists from Skoltech, MIPT, and ITMO developed an optical component that helps manage the properties of a terahertz beam and split it into several channels.
High Density Packaging User Group Announces Shenzhen Kinwong Electronic Co., Ltd. Membership
05/20/2024 | High Density Packaging User GroupHigh Density Packaging User Group (HDP) is pleased to announce that Shenzhen Kinwong Electronic Co., Ltd. (Kinwong) has become a member.
Real Time with… IPC APEX EXPO 2024: Precision Tools and Problem-solving With Perfect Point
05/14/2024 | Real Time with...IPC APEX EXPOIn an interview with Guest Editor Dan Beaulieu, Alex Girardot, a field applications engineer with Perfect Point, shares his experiences with precision tooling. Alex also discusses a challenging project involving thick boards and small diameter holes in which Carbonite tools with a hybrid design were used. They also discuss the trend toward smaller hole sizes.
epoxySet Launches EC-1015HP - High Temperature, Crack Resistant Epoxy Potting
05/13/2024 | epoxySetepoxySet introduces the EC-1015HP epoxy potting compound. This heat cure system is designed for temperature cycling from -55 to 180°C with significantly better crack resistance than traditional rigid epoxies. As a low viscosity encapsulant, it is used for large and small potting applications with fragile components.
D Coupon Testing and Data Insights With GreenSource Fabrication
04/17/2024 | Marcy LaRont, PCB007 MagazineMarcy LaRont spoke with Steve Karas of GreenSource Fabrication at the SMTA UHDI conference in March. He presented a case study that GreenSource undertook with a customer on critical via reliability with advanced materials and used the experience to highlight the importance and effectiveness of D coupon testing. He also discussed GreenSource’s approach to data aggregation and a new system they developed to use collected data effectively.