Illinois Researcher Receives DARPA Contract to Design a Hybrid Robot
June 7, 2016 | University of Illinois at Urbana-ChampaignEstimated reading time: 3 minutes
Illinois researcher Hae-Won Park has been awarded a Robotics Fast Track contract from the Defense Advanced Research Projects Agency (DARPA) to design a hybrid robot that can glide, land, and walk.
His ground-breaking design connects two widely researched robot forms – UAVs and quadruped robots – and is inspired by the flying squirrel, or Glaucomys volans. This animal can glide between trees and walk on branches to harvest food and escape from predators.
Park’s robot would be dropped from an aerial vehicle, glide like a flying squirrel, then land and continue walking on a variety of terrains, with proposed applications in reconnaissance missions, military scouting, and disaster response efforts, particularly in difficult-to-access or hazardous environments.
Other robots that can walk or fly and that are used in these situations, are often met with a number of challenges, such as limited battery life, constrained mobility in tight spaces, and an inability to travel long distances.
Park’s flying squirrel will address these flaws. The combined mobility of walking and flying will give the bots the large range of coverage of existing flying robots as well as the long-lasting operational hours of a ground vehicle. Additionally, the ability to gather information about environmental conditions is crucial to saving lives. Thus, they can be used independently or in swarms to share environmental awareness via a mobile sensor network.
While there have been other robots of a similar design, most research has focused on very small robots that could not complete the missions Park believes his robot can accomplish. These smaller bots also tend not to boast complex combinations between walking and gliding, and as a result, they cannot walk well and their wings lack active control.
Park, an assistant professor in the Department of Mechanical Science and Engineering at the University of Illinois at Urbana-Champaign, got the idea for the flying squirrel model while watching a National Geographic Channel documentary called “Super Squirrel” that depicts the animal jumping and gliding between trees to navigate the woods.
“Their aerodynamic maneuvers are so elegant, dynamic, and efficient,” Park said. “They use their limbs and tails, changing the shape of the wing to steer and control the gliding. That’s where I got my inspiration.”
His design includes development of soft silicone wing structures that will attached to the robot’s limbs and allow it to glide. They will feature adjustable stiffness and morphing abilities, and will serve as a shape-morphing aerodynamic control surface when stretched.
“An ideal material would be both compliant and strong, such that the wing can be stretched to increase the aerodynamically active surface area when gliding and be furled to not obstruct while walking,” Park said.
This is part of what he calls a multifunctional body frame, i.e. one that has the physical structure to allow the bot to walk and glide.
The body frame will be 3D-printed with lightweight materials – allowing for fast prototyping – like carbon fiber composite material, engineered plastics, and compliant resins. Other parts will be off-the-shelf components, lowering the cost enough to make the robots expendable after use. The entire bot is estimated to weigh only about 1.5 pounds.
Park directs the Dynamic Robotics Lab at Illinois. He earned a PhD in mechanical engineering from the University of Michigan in 2012, a master’s degree in mechanical engineering in 2007 from Yonsei University, and a bachelor’s degree, also in mechanical engineering, from Yonsei University in 2005. After holding positions as a Postdoctoral Associate and a Research Scientist at MIT, he joined the MechSE Department at Illinois in September 2015.
DARPA is an agency of the U.S. Department of Defense responsible for the development of emerging technologies for use by the military.
Suggested Items
Podcast Review: On the Line with… Designing for Reality
05/09/2024 | Duane Benson, Positive Edge LLCAs a technologist, if I were forced to come up with just one recurring theme that I might call a professional “nemesis,” it would be the difference between theory and reality. A lot of technology we have at our disposal works well in theory but falls short when reality hits. That’s not the only reason I chose to listen to and review On the Line with… Designing for Reality, featuring a series of conversations with ASC Sunstone’s Matt Stevenson, but it certainly helped that the title caught my eye.
EMA Webinar: Next Generation MCAD/ECAD for SOLIDWORKS
05/09/2024 | EMA Design AutomationLearn how the MCAD and ECAD experts at Hawk Ridge and EMA can help you solve your MCAD/ECAD integration challenges with this unique collaboration environment.
Sondrel Awarded New Video Processor ASIC Design and Supply Contract
05/09/2024 | SondrelSondrel, a leading provider of ultra-complex custom chips for leading global technology brands, is pleased to announce that it has won a major ASIC design and supply contract for a next generation, video processing chip.
Connect the Dots: Designing for Reality—The Pre-Manufacturing Process
05/08/2024 | Matt Stevenson -- Column: Connect the DotsI have been working with Nolan Johnson on a podcast series about designing PCBs for the reality of manufacturing. By sharing lessons learned over a long career in the PCB industry, we hope to shorten learning curves and help designers produce better boards with less hassle and rework. Episode 2 deals with the electronic pre-manufacturing process. Moving from CAD (computer-aided design) to CAM (computer-aided manufacturing) is a key step in PCB manufacturing. CAM turns digital designs into instructions that machines can use to actually build the PCB.
Indium Corporation to Showcase HIA Materials at ECTC
05/07/2024 | Indium CorporationAs an industry leader in innovative materials solutions for semiconductor packaging and assembly, Indium Corporation® will feature its advanced products designed to meet the evolving challenges of heterogeneous integration and assembly (HIA) and fine-pitch system-in-package (SiP) applications at the 74th Electronic Components and Technology Conference (ECTC), May 28‒31, in Denver, Colorado.
Copyright © 2024 I-Connect007 | IPC Publishing Group Inc. All rights reserved.
Log in