-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueAdvancing the Advanced Materials Discussion
Moore’s Law is no more, and the advanced material solutions to grapple with this reality are surprising, stunning, and perhaps a bit daunting. Buckle up for a dive into advanced materials and a glimpse into the next chapters of electronics manufacturing.
Inventing the Future With SEL
Two years after launching its state-of-the-art PCB facility, SEL shares lessons in vision, execution, and innovation, plus insights from industry icons and technology leaders shaping the future of PCB fabrication.
Sales: From Pitch to PO
From the first cold call to finally receiving that first purchase order, the July PCB007 Magazine breaks down some critical parts of the sales stack. To up your sales game, read on!
- Articles
- Columns
- Links
- Media kit
||| MENU - pcb007 Magazine
Mentor Graphics’ Q3 Results Exceed Guidance
November 22, 2016 | Business WireEstimated reading time: 3 minutes
Mentor Graphics Corporation today announced financial results for the company’s fiscal third quarter ended October 31, 2016. The company reported revenues of $322.5 million, GAAP earnings per share of $0.37 and non-GAAP earnings per share of $0.50.
Fiscal Third Quarter Performance
- Book to bill was a record for a third quarter and solidly above 1.0 for the second consecutive quarter.
- Annualized fee growth for top 10 renewals was 60 percent overall with fees from systems customers growing over 160 percent and those from integrated circuit (IC) customers growing 35 percent.
- Average term length for renewals in the top 10 deals was 3.1 years.
- Emulation product revenue, up 100 percent year over year, included 4 new customers for the second consecutive quarter.
- GAAP gross margin was 84.1 percent. Non-GAAP gross margin of 84.9 percent is the highest for a Q3 in the last five years and 340 basis points higher than last quarter.
- GAAP operating expenses were $215 million. Non-GAAP operating expenses of $202 million were on guidance and flat year over year.
“Mentor’s third quarter results solidly exceeded revenue and earnings-per-share guidance,” said Walden C. Rhines, chairman and CEO of Mentor Graphics. “Book to bill was significantly above one with strength in both semiconductor and system accounts. Growth of the annual run-rate in our top 10 customers was a strong 60 percent in the third fiscal quarter. After quarter end, on November 14, we announced an agreement whereby Siemens will acquire Mentor Graphics. Joining forces with Siemens will enable Mentor to achieve the next level of success for our customers and employees.”
During the quarter Mentor Graphics acquired Galaxy Semiconductor, a leading provider of test data analysis and defect reduction software for the semiconductor industry. The company further extended its offerings within the Calibre® and Analog FastSPICE (AFS™) platforms to support TSMC 7 nm and 16 FFC FinFET process technologies. Mentor received two Partner of the Year Awards from TSMC for joint delivery of the 7 nm mobile design platform and the Integrated Fan-Out (INFO) design solution.
Mentor announced a partnership with embedded middleware vendor Real-Time Innovations (RTI) for secure embedded systems communications in industrial, medical and mil-aero applications. The company also released the new Xpedition® multi-board system design solution enabling multi-discipline team collaboration, as well as advanced technologies in the Xpedition flow to enable design and verification of 3D rigid-flex structures. In automotive news, the company announced a joint agreement with Telemotive AG to provide smart charging technology for plug-in vehicles.
“Bookings were up 50 percent over the same quarter a year ago,” said Gregory K. Hinckley, president of Mentor Graphics. “Revenue of $323 million is a record for a third quarter and up 11 percent from the same period a year ago while non-GAAP earnings per share of $0.50 were up 78 percent year over year. Robust revenue combined with our continued attention to expense control resulted in a GAAP operating margin of 18 percent. In addition non-GAAP operating margin of 22 percent drove non-GAAP operating profits up over 60 percent year over year.”
Outlook
On November 14, 2016, the company announced that it had entered into a merger agreement under which Siemens will acquire Mentor Graphics. As a result of the acquisition announcement, the company will not provide an outlook for future financial results and is withdrawing all previously issued financial guidance.
Dividend
The company announced a quarterly dividend of $0.055 per share. The dividend is payable on January 3, 2017 to shareholders of record at the close of business on December 8, 2016.
Fiscal Year Definition
Mentor Graphics Corporation’s fiscal year runs from February 1 to January 31. The fiscal year is dated by the calendar year in which the fiscal year ends. As a result, the first three fiscal quarters of any fiscal year will be dated with the next calendar year, rather than the current calendar year.
About Mentor Graphics
Mentor Graphics Corporation is a world leader in electronic hardware and software design solutions, providing products, consulting services and award-winning support for the world’s most successful electronic, semiconductor and systems companies. Established in 1981, the company reported revenues in the last fiscal year of approximately $1.18 billion. Corporate headquarters are located at 8005 S.W. Boeckman Road, Wilsonville, Oregon 97070-7777. For more information, click here..
Testimonial
"Advertising in PCB007 Magazine has been a great way to showcase our bare board testers to the right audience. The I-Connect007 team makes the process smooth and professional. We’re proud to be featured in such a trusted publication."
Klaus Koziol - atgSuggested Items
Mouser Electronics Celebrates Its 2025 Best-in-Class Award Winners
10/01/2025 | BUSINESS WIREMouser Electronics, Inc., the New Product Introduction (NPI) leader™ empowering innovation, is pleased to announce the 2025 recipients of the Mouser Best-in-Class Awards.
Elementary Mr. Watson: Chasing Checkmarks, Not Signal Integrity
10/01/2025 | John Watson -- Column: Elementary, Mr. WatsonFor the September 2025 issue of Design007 Magazine on signal integrity, I explored how the PCB is similar to a military obstacle course: walls that sap energy like impedance mismatches, barbed wire that cuts like crosstalk, and mud pits that drag a signal down like attenuation. The takeaway was clear that a PCB is not a flat drawing; it's an electromagnetic ecosystem filled with hazards that test every signal that dares to cross it. The real danger lies not in the obstacles themselves, but in the fact that many designers never see them.
Target Condition: Rethinking the PCB Stackup Recipe
10/01/2025 | Kelly Dack -- Column: Target ConditionMarie Antoinette is attributed with saying, “Let them eat cake,” but historians now agree she likely never said it. It was probably revolutionary propaganda to paint her as out of touch with the starving masses. Yet, the phrase still lingers, and oddly enough, it applies to the world of PCB design.
Connect the Dots: Evolution of PCB Manufacturing—Lamination
10/02/2025 | Matt Stevenson -- Column: Connect the DotsWhen I wrote The Printed Circuit Designer's Guide to...™ Designing for Reality, it was not a one-and-done effort. Technology is advancing rapidly. Designing for the reality of PCB manufacturing will continue to evolve. That’s why I encourage designers to stay on top of the tools and processes used during production, to ensure their designs capitalize on the capabilities of their manufacturing partner.
Siemens, ASE Collaborate on Workflows for ASE’s VIPack Advanced Packaging Platform
09/25/2025 | SiemensSiemens Digital Industries Software announced that it is collaborating with Advanced Semiconductor Engineering, Inc. (ASE), the leading global provider of semiconductor manufacturing services in assembly and test, to develop 3Dblox-based workflows for the ASE VIPack™ platform using Siemens’ Innovator3D IC™ solution, which is fully certified for the 3Dblox standard..