Trouble in Your Tank: Metallizing Flexible Circuit Materials—Mitigating Deposit Stress
It’s Only Common Sense: Sales as a Team Sport
Dan’s Biz Bookshelf: ‘In Defense of a Liberal Education’
Rogers to Highlight High-speed Laminates and Next-Gen Thin Materials at DesignCon 2020
January 13, 2020 | Rogers CorporationEstimated reading time: 3 minutes
Rogers Corporation will exhibit at DesignCon in Santa Clara, CA (at booth #421) highlighting some of its high-performance circuit materials used in multilayer structures which include a family of thin laminates, bonding materials, and sheeted copper foil options.
DesignCon is a premiere event for electronic design engineers working on circuit and system levels. Held at the Santa Clara Convention Center, the event takes place January 29-30.
Visitors to Rogers’ booth will learn more about:
XtremeSpeed™ RO1200™ Laminates
XtremeSpeed RO1200 high speed, extremely low loss laminates, with a low dielectric constant of 3.05, and a maximum dissipation factor of 0.0017 @10 GHz, provide outstanding signal integrity, reduced signal skew, and reduced cross-talk. Combined with superior thermal/mechanical performance, low CTE, and a halogen free UL 94 V-0 rating, these laminates are well suited for the most demanding high layer count applications.
As channel speeds rise to 112Gbps and beyond, hardware designers need high performance circuit materials with superior electrical properties for applications like Network Infrastructure, High Performance Computing, and Test & Measurement. XtremeSpeed RO1200 circuit materials are engineered to meet the unique electrical and thermal/mechanical demands of high speed designs and enable system designers the flexibility to design leading edge systems that maximize data throughput and minimize latency in performance demanding applications.
RO4000® Products for Multilayer Structures
Next generation products designed to meet the existing and emerging needs of advanced millimeter wave multilayer designs. RO4835T™ laminates, offered in a 2.5 mil, 3 mil and 4 mil core thickness, are 3.3 Dk, low loss, spread glass reinforced, ceramic filled thermoset materials designed for inner-layer use in multilayer board designs, and they complement RO4835™ laminates when thinner cores are needed.
RO4450T™ 3.2-3.3 Dk, low-loss, spread glass reinforced, ceramic filled bonding materials were designed to complement RO4835T laminates and the existing RO4000 laminate family, and come in 2.5, 3, 3.5, 4, 4.5, 5 or 6 mil thicknesses.
RO4835T laminates and RO4450T bonding materials exhibit excellent Dk control for repeatable electrical performance, a low z-axis expansion for plated through-hole reliability, and are compatible with standard epoxy/glass (FR-4) processes. These materials are an excellent choice for multilayer designs requiring sequential laminations, as fully cured RO4000 products are capable of withstanding multiple lamination cycles. RO4835T laminates and RO4450T bondplys have the UL 94 V-0 flame retardant rating, and are compatible with lead-free processes.
Lastly, CU4000™ and CU4000 LoPro® Foils are sheeted foil options for designers looking for foil lamination builds, and provide good outer layer adhesion when used with RO4000 products.
RO3003G2™ high frequency laminates build on Rogers’ industry-leading RO3003™ platform to provide designers with improved insertion loss and reduced Dk variation. The combination of Rogers’ optimized resin and filler content along with the introduction of very low-profile ED copper translates to Dk of 3.00 @ 10 GHz (clamped stripline method) and 3.07 @ 77 GHz (microstrip differential phase length method). RO3003G2 laminates also show very low insertion loss of 1.3dB/inch for 5 mil laminates as measured by the microstrip differential phase length method.
CLTE-MW™ laminates are reinforced with spread glass, which along with a high filler loading help minimize the high frequency glass weave effects on electromagnetic wave propagation. The woven glass reinforcement also provides excellent dimensional stability. Other key features of the laminate include low z-axis CTE (30ppm/°C) for excellent plated through hole reliability, a low loss tangent of 0.0015 at 10 GHz to enable low loss designs, and low moisture absorption of 0.03% to ensure stable performance in a range of operating environments. Thermal conductivity of 0.42 W/(m.K) enables heat dissipation in aggressive designs along with a high dielectric strength of 630 V/mil to ensure good z-axis insulation between conductor layers. The UL 94 V-0 flammability rating enables the use of CLTE-MW laminates in commercial applications including Amplifiers, Antennas, Baluns, Couplers and Filters.
Technical Conference Presentation
On the technical conference side, Al Horn, Rogers Research Fellow, will participate in a panel discussion “Next Generation Materials for High Speed Digital Design” on Jan. 29, from 3:45 – 5:00 p.m.
About Rogers Corporation
Rogers Corporation (NYSE:ROG) is a global leader in engineered materials to power, protect, and connect our world. With more than 180 years of materials science experience, Rogers delivers high-performance solutions that enable clean energy, internet connectivity, and safety and protection applications, as well as other technologies where reliability is critical. Rogers delivers Power Electronics Solutions for energy-efficient motor drives, e-Mobility and renewable energy; Elastomeric Material Solutions for sealing, vibration management and impact protection in mobile devices, transportation interiors, industrial equipment and performance apparel; and Advanced Connectivity Solutions for wireless infrastructure, automotive safety and radar systems. Headquartered in Arizona (USA), Rogers operates manufacturing facilities in the United States, China, Germany, Belgium, Hungary, and South Korea, with joint ventures and sales offices worldwide. For more information, visit www.rogerscorp.com.
Share on:
Testimonial
"Our marketing partnership with I-Connect007 is already delivering. Just a day after our press release went live, we received a direct inquiry about our updated products!"
Rachael Temple - AlltematedSuggested Items
Advancing Electrolytic Copper Plating for AI-driven Package Substrates
08/05/2025 | Dirk Ruess and Mustafa Oezkoek, MKS’ AtotechThe rise of artificial intelligence (AI) applications has become a pivotal force driving growth in the server industry. Its challenging requirements for high-frequency and high-density computing are leading to an increasing demand for development of advanced manufacturing methods of package substrates with finer features, higher hole densities, and denser interconnects. These requirements are essential for modern multilayer board (MLB) designs, which play a critical role in AI hardware. However, these intricate designs introduce considerable manufacturing complexities.
Statement from the Global Electronics Association on the July 2025 Tariff on Copper Foil and Electronics-Grade Copper Inputs
07/31/2025 | Global Electronics AssociationWe are disappointed by today’s decision to impose a 50% tariff on imported copper foil and other essential materials critical to electronics manufacturing in the United States.
Trouble in Your Tank: Metallizing Flexible Circuit Materials—Mitigating Deposit Stress
08/04/2025 | Michael Carano -- Column: Trouble in Your TankMetallizing materials, such as polyimide used for flexible circuitry and high-reliability multilayer printed wiring boards, provide a significant challenge for process engineers. Conventional electroless copper systems often require pre-treatments with hazardous chemicals or have a small process window to achieve uniform coverage without blistering. It all boils down to enhancing the adhesion of the thin film of electroless copper to these smooth surfaces.
Considering the Future of Impending Copper Tariffs
07/30/2025 | I-Connect007 Editorial TeamThe Global Electronics Association is alerting industry members that a potential 50% tariff on copper could hit U.S. electronics manufacturers where it hurts.
Connect the Dots: Sequential Lamination in HDI PCB Manufacturing
07/31/2025 | Matt Stevenson -- Column: Connect the DotsAs HDI technology becomes mainstream in high-speed and miniaturized electronics, understanding the PCB manufacturing process can help PCB design engineers create successful, cost-effective designs using advanced technologies. Designs that incorporate blind and buried vias, boards with space constraints, sensitive signal integrity requirements, or internal heat dissipation concerns are often candidates for HDI technology and usually require sequential lamination to satisfy the requirements.