Royal Flex Circuits Supports the Production of Ventilators for Medtronic
March 25, 2020 | Royal Flex CircuitsEstimated reading time: 1 minute
Companies across the nation are ramping up their production lines to increase the ventilator capacity in the United States and around the world. But not all companies are qualified to perform the work. Only a fraction of the approximately 100 PCB manufacturing companies in the United States is capable of quickly fabricating and assembling the necessary circuit boards.
Royal Flex Circuits, in Santa Fe Springs, California is uniquely positioned to help out in the crisis. Its new production facility, less than a year old, features the latest machinery, hardware, and production methods. The company has an inventory of copper-clad cores and prepreg, allowing it to start production as soon as the design files arrived from ventilator manufacturers.
Victor Hemingway, President of Royal Flex Circuits, said, “We have been producing circuit boards for Medtronic ventilators for over 10 years. We have extended production hours and now have two shifts of engineers and production-line employees making the circuit boards that control ventilators. Our employees are putting in long hours, but we are so proud to be helping in this time of great need.”
Throughout the COVID-19 epidemic, as many as “960,000 Americans will require ventilatory support” (US Resource Availability for COVID-19, Society of Critical Care Medicine, March 2020). A survey in 2009 identified approximately 160,000 ventilators in hospitals with another 12,700 in the Strategic National Stockpile (Worst -Case Estimates for US Coronovirus Deaths, New York Times, March 13, 2020). The large disparity between those two numbers means that potentially hundreds of thousands of Americans will not have the medical resources they need.
Royal Flex Circuits manufactures rigid, rigid-flex, and flexible printed circuits. “Fabricating and assembling flexible printed circuit boards is a very complex process that requires a fair amount of materials, a lot of labor and great attention to detail,” said Hemingway. “But done correctly, the net result is a product that helps saves lives.”
Suggested Items
Atotech to Participate at KPCA Show 2024
09/03/2024 | AtotechMKS’ Atotech will participate in this year’s KPCA Show 2024 in Incheon, held at Songdo Convensia from September 4-6, 2024.
Victory Announces Breakthrough in PCB Technology with New Product Launch
08/29/2024 | openPRShenzhen Victory Electronics Technology Co., Ltd., a leader in the printed circuit board (PCB) manufacturing industry, is proud to announce the successful development of a groundbreaking new product.
Connect the Dots: Designing for Reality—Electroless Copper
08/28/2024 | Matt Stevenson -- Column: Connect the DotsRoll up your sleeves because it's time to get messy. In a recent episode of I-Connect007’s On the Line with… podcast, we discussed electroless copper deposition. This process deposits a copper layer into the through-holes and vias of what will eventually be a PCB. Electroless copper deposition feels like a black box to many people. It sort of looks like a black box, too. The boards go in one side, come out the other, and emerge differently. So, let's crack open that black box and look inside.
Maximizing ROI Through Better Wet Process Control
08/20/2024 | I-Connect007 Editorial Team“When things get out of control, the variation in your wet process begins,” says Mike Carano,. “Just because they look like good boards and may even pass electrical test, it does not necessarily mean you have good boards. Once the chemistry is headed toward the right or left side of the process control parameter cliff, the plating is compromised. If the copper is thinner than it should be, when the customer puts it into service, the board may fail after 500 cycles vs. the requisite 1,000 or 2,000 cycles. The root cause issue is that you plated 7/10ths of a mil of copper instead of one-mil of copper because you were not controlling your process. The fact that you passed your own electric test becomes inconsequential.”
The Chemical Connection: Controlling an Alkaline Etch Bath With Low Copper Loading
08/07/2024 | Don Ball -- Column: The Chemical ConnectionThis month, I wanted to continue my discussion on how much process control is actually needed for high-density circuit production. However, in the last month, I have been called on to help with a specific process control problem: how to control an alkaline etch bath when you’re not etching much copper. This problem has been cropping up more frequently as smaller shops (and a few larger ones) concentrate on low-volume, high-value plated through-hole panels such as prototypes, resistor cores, etc.