NASA’s Mars Helicopter Survives First Cold Martian Night on Its Own
April 6, 2021 | NASA JPLEstimated reading time: 4 minutes

Making it through the frigid Martian temperatures after being deployed by NASA’s Perseverance rover is a major milestone for the small rotorcraft.
NASA’s Ingenuity Mars Helicopter has emerged from its first night on the surface of Mars.
Evening temperatures at Jezero Crater can plunge as low as minus 130 degrees Fahrenheit (minus 90 degrees Celsius), which can freeze and crack unprotected electrical components and damage the onboard batteries required for flight. Surviving that first night after being deployed from where it was attached to the belly of NASA’s Perseverance rover on April 3 is a major milestone for the 4-pound (1.8 kilograms) rotorcraft. In the days to come, Ingenuity will be the first aircraft to attempt powered, controlled flight on another planet.
“This is the first time that Ingenuity has been on its own on the surface of Mars,” said MiMi Aung, Ingenuity project manager at NASA’s Jet Propulsion Laboratory in Southern California. “But we now have confirmation that we have the right insulation, the right heaters, and enough energy in its battery to survive the cold night, which is a big win for the team. We’re excited to continue to prepare Ingenuity for its first flight test.”
Devising a craft small enough to fit onto the rover, light enough to fly in Mars’ thin atmosphere, yet hardy enough to withstand the Martian cold presented significant challenges. To ensure the solar array atop the helicopter’s rotors could begin getting sunlight as soon as possible, Perseverance was instructed to move away from Ingenuity shortly after deploying it.
Until the helicopter put its four legs onto the Martian surface, Ingenuity remained attached to the belly of the rover, receiving power from Perseverance, which touched down at Jezero Crater on Feb. 18. The rover serves as a communications relay between Ingenuity and Earth, and it will use its suite of cameras to observe the flight characteristics of the solar-powered helicopter from “Van Zyl Overlook.”
The sole mission of Ingenuity, a technology demonstration, is to conduct flight tests in the thin atmosphere of Mars; the helicopter carries no science instruments. Within 30 Martian days, or sols (a Martian day is 24.6 hours), on the surface, Ingenuity will complete its testing, and Perseverance’s scientific exploration of Jezero Crater will kick into high gear.
“Our 30-sol test schedule is frontloaded with exciting milestones,” said Teddy Tzanetos, deputy operations lead for the Ingenuity Mars Helicopter at JPL. “Whatever the future holds, we will acquire all the flight data we can within that timeframe.”
The Month of Ingenuity
On April 4, Perseverance downlinked the first of the images of the helicopter on the surface of Mars. Taken by the rover’s rear left Hazard Avoidance camera, the image shows the helicopter’s rotor blades still stacked in alignment on top of each other (a configuration used to save room during the trip to Mars) and its four footpads firmly planted into the surface of Mars.
For the next two days, Ingenuity will collect information about how well the thermal-control and power systems perform now that the small helicopter is standing on its own in the Mars environment. That information will be used to fine tune Ingenuity’s thermal-control system to help it survive the harsh Mars nights through the entire flight experiment period.
On April 7, the restraints that have been holding the rotor blades together since before launch are scheduled to be released. If the mission team meets that milestone, the next several sols will involve more testing of the rotor blades as well as the motors that drive them. There are also checkouts of the inertial measurement unit (an electronic device that measures a body’s orientation and angular rate) and onboard computers tasked with autonomously flying the helicopter. Additionally, the team will continue to monitor the helicopter’s energy performance, including assessment of solar-array power and state of charge of the craft’s six lithium ion batteries.
If all goes well with each of the myriad preflight checks, Ingenuity’s first attempt to lift off from the middle of its 33-by-33-foot (10-by-10-meter) “airfield” – chosen for its flatness and lack of obstructions – will be no sooner than the evening of April 11.
Subsequent flight tests will be scheduled throughout the Month of Ingenuity, with Perseverance’s cameras providing plenty of high-definition images of the historic mission.
More About Ingenuity
The Ingenuity Mars Helicopter was built by JPL, which also manages this technology demonstration project for NASA Headquarters. It is supported by NASA’s Science Mission Directorate, the NASA Aeronautics Research Mission Directorate, and the NASA Space Technology Mission Directorate. NASA’s Ames Research Center and Langley Research Center provided significant flight performance analysis and technical assistance.
At NASA Headquarters, Dave Lavery is the program executive for the Ingenuity Mars Helicopter. At JPL, MiMi Aung is the project manager and J. (Bob) Balaram is chief engineer.
JPL, which is managed for NASA by Caltech in Pasadena, California, built and manages operations of the Ingenuity Mars Helicopter.
Suggested Items
Global PCB Connections: Embedded Components—The Future of High-performance PCB Design
06/19/2025 | Jerome Larez -- Column: Global PCB ConnectionsA promising advancement in this space is the integration of embedded components directly within the PCB substrate. Embedded components—such as resistors, capacitors, and even semiconductors—can be placed within the internal layers of the PCB rather than mounted on the surface. This enables designers to maximize available real estate and improve performance, reliability, and manufacturability.
Preventing Surface Prep Defects and Ensuring Reliability
06/10/2025 | Marcy LaRont, PCB007 MagazineIn printed circuit board (PCB) fabrication, surface preparation is a critical process that ensures strong adhesion, reliable plating, and long-term product performance. Without proper surface treatment, manufacturers may encounter defects such as delamination, poor solder mask adhesion, and plating failures. This article examines key surface preparation techniques, common defects resulting from improper processes, and real-world case studies that illustrate best practices.
SMTA Releases Final Batch of Training Resources Donated by Bob Willis
05/29/2025 | SMTAThe Surface Mount Technology Association (SMTA) announces the release of several more webinars, poster sets, and photo libraries to conclude a generous donation from renowned industry expert Bob Willis.
American Standard Circuits to Exhibit and Speak at SMTA Oregon Expo
05/14/2025 | American Standard CircuitsAnaya Vardya, President, and CEO of American Standard Sunstone Circuits has announced that his company will be exhibiting SMTA Oregon Expo & Tech Forum to be held on May 20 at the Wingspan Events and Conference Center in Hillsboro, Oregon.
EIPC Summer Conference 2025: PCB Innovation in Edinburgh
04/18/2025 | EIPCEIPC have very wisely selected this wonderful city in Scotland as the venue for their Summer Conference on June 3-4. Whilst delegates will be distilling the proven information imparted by the speakers in the day, in the evening they will be free spirits at the Conference Dinner.