DOCOMO Develops Solution to Create High-frequency Mobile Cells
January 18, 2022 | ACN NewswireEstimated reading time: 2 minutes
NTT DOCOMO, INC. announced that it has developed an antenna system capable of creating a high-frequency mobile communication cell when a small (roughly one cubic centimeter) piece of plastic is placed on top of a dielectric waveguide. The solid plastic cube serves as an antenna by creating a "leak" from the cable to propagate signals up to several tens of meters. DOCOMO successfully tested the system with an ultra-high-frequency 60 GHz radio signal, similar to those expected to be used in future 6G networks.
DOCOMO envisions its simple, low-cost solution being used to create instant mobile environments in indoor areas not reachable with highly directional high-frequency signals propagated by outdoor base stations.
This system, named "Drop-n-Prop Antenna," takes advantage of the physical phenomenon of radio waves leaking (propagating) from the contact point created by placing ("dropping") a small piece of plastic on top of a dielectric waveguide carrying the signal.
In the trial, DOCOMO constructed a communication area by running a rod-shaped dielectric waveguide made of polytetrafluoroethylene into an indoor area that was inaccessible to external mobile signals. The waveguide was embedded in a length of polystyrene-foam board with one side barely exposed to allow contact with antennas. Multiple communication cells were created simultaneously by placing antennas along various parts of the waveguide. Signal coverage and direction were controlled by changing the material, shape and positioning of the antennas.
Both millimeter waves (28 GHz) for 5G and higher frequencies (60 GHz, etc.) expected to be used for 6G travel in very straight (rectilinear) lines. It is difficult for such waves to reach devices not in a base station's direct line of sight, or if the signals are blocked by surrounding obstacles (walls, equipment, etc.). DOCOMO's simple, low-cost antenna system being announced today merely requires a rod-shaped dielectric waveguide to be run into an area and then embedded in the floors, walls, ceilings, furniture or work surfaces. Communication areas can be constructed easily and unobtrusively in offices, factories, etc. and reconfigured quickly and flexibly just by moving the antenna(s) as required.
The new antenna system also will help to lower energy use by efficiently propagating signals to desired areas only, thereby eliminating wasteful usage of power to propagate signals in areas where communication is not required.
DOCOMO will begin verifying a system using 28 GHz 5G radio signals in the first half of fiscal 2022 starting this April, aiming to introduce a commercial version of its new antenna system as soon as possible.
Suggested Items
Cadence, TSMC Collaborate on Wide-Ranging Innovations to Transform System and Semiconductor Design
04/25/2024 | Cadence Design SystemsCadence Design Systems, Inc. and TSMC have extended their longstanding collaboration by announcing a broad range of innovative technology advancements to accelerate design, including developments ranging from 3D-IC and advanced process nodes to design IP and photonics.
Siemens’ Breakthrough Veloce CS Transforms Emulation and Prototyping with Three Novel Products
04/24/2024 | Siemens Digital Industries SoftwareSiemens Digital Industries Software launched the Veloce™ CS hardware-assisted verification and validation system. In a first for the EDA (Electronic Design Automation) industry, Veloce CS incorporates hardware emulation, enterprise prototyping and software prototyping and is built on two highly advanced integrated circuits (ICs) – Siemens’ new, purpose-built Crystal accelerator chip for emulation and the AMD Versal™ Premium VP1902 FPGA adaptive SoC (System-on-a-chip) for enterprise and software prototyping.
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation are proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia. on their first installation of Taiyo Circuit Automation DP3500 coater.
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.
Lockheed Martin Successfully Transitions Long Range Discrimination Radar To The Missile Defense Agency
04/23/2024 | Lockheed MartinThe Long Range Discrimination Radar (LRDR) at Clear Space Force Station in Clear, Alaska, completed DD250 final acceptance and was officially handed over to the Missile Defense Agency in preparation for an Operational Capability Baseline (OCB) decision and final transition to the Warfighter. In addition, prior to this transition, the system has started Space Domain Awareness data collects for the United States Space Force.