-
- News
- Books
Featured Books
- pcb007 Magazine
Latest Issues
Current IssueThe Hole Truth: Via Integrity in an HDI World
From the drilled hole to registration across multiple sequential lamination cycles, to the quality of your copper plating, via reliability in an HDI world is becoming an ever-greater challenge. This month we look at “The Hole Truth,” from creating the “perfect” via to how you can assure via quality and reliability, the first time, every time.
In Pursuit of Perfection: Defect Reduction
For bare PCB board fabrication, defect reduction is a critical aspect of a company's bottom line profitability. In this issue, we examine how imaging, etching, and plating processes can provide information and insight into reducing defects and increasing yields.
Voices of the Industry
We take the pulse of the PCB industry by sharing insights from leading fabricators and suppliers in this month's issue. We've gathered their thoughts on the new U.S. administration, spending, the war in Ukraine, and their most pressing needs. It’s an eye-opening and enlightening look behind the curtain.
- Articles
- Columns
- Links
- Media kit
||| MENU - pcb007 Magazine
I-Connect007 Editor’s Choice: Five Must-Reads for the Week
December 2, 2022 | Nolan Johnson, I-Connect007Estimated reading time: 2 minutes

Normally, the holiday season is a slow(ish) news time, but this year just feels different. My opinion is that the technology industry banked up a whole bunch of innovations and new products during the pandemic disruptions, which are coming to market as quickly as possible. The November/December news is full of technology discussion, as my selections this week clearly demonstrate.
We have a discussion on additively manufactured electronics, as well as a high-level look at fabrication for the UHDI market—both emerging markets. I also noticed that our readers were quite interested in industry reports on U.S. semiconductor industry challenges, and a forward look at the drivers in the flexible PCB fabrication market, so I was sure to include the links again. Finally, I thought I’d share the news item about a new missile guidance system prototype test that caught reader attention and which has garnered quite a bit of attention.
3D Electronic Devices With Additive Manufacturing
Published November 29
In the news on Dec. 1, Nano Dimension issued a press release announcing Q3 2022 results where the company shares that it is on track to increase revenue by 10X over 2020’s results. That news shines a spotlight on this article from Shavi Spinzi discussing the possibilities of additively manufactured electronics.
Global Flexible PCB Market Report 2022: Rising Use in the Aerospace and Aviation Sector Boosts Growth
Published November 25
My recent conversations with flex manufacturers all have a familiar tone: “We’re really busy, capacity is maxed out.” Well, this quote from the Flexible PCB Marketplace Report news release corroborates what I’m hearing: “The [flex] market is expected to surge in the coming years due to the rising use of flexible printed circuit boards in consumer electronics, especially smartphones, laptops, displays, and other electronic devices. According to official industrial sources, around 1.5 billion smartphones were sold in the year 2019.” The article discusses automotive, aviation and aerospace.
Understanding the UHDI Market
Published November 28
This interview with Meredith LaBeau and Todd Brassard from Calumet Electronics included this in the setup to the conversation, “The more we investigate UHDI in the current market, the more advanced packaging becomes a part of the conversation. The two emerging technologies lean on each other for their overall success. UHDI is the method by which state-of-the-art advanced packaging will be fabricated; substrates are creating a market for UHDI capabilities.” In many ways, Calumet is blazing the trail for nimble PCB fabricators to move forward into capabilities that support advanced packaging. Clearly, readers were interested this week in what LaBeau and Brassard had to say.
New Report Identifies Challenges to Continued U.S. Leadership in Semiconductor Design, Innovation
Published November 30
This report from the Semiconductor Industry Association (with Boston Consulting Group) identifies three key areas the U.S. must address in the administration of the CHIPS Act in order to maintain a leadership position: Design and R&D investment needs are on the rise, there is a shortage of domestic design talent, and open access to global markets is under pressure. Take a read and see if you agree.
PAC-3 Intercepts Target In Successful Test of Lockheed Martin Remote Interceptor Guidance
Published November 25
Lockheed Martin announced that their new missile communication device connected with a U.S. Army PAC-3 missile in flight. This prototype system is seen as a step forward in missile guidance systems.
Suggested Items
Delta Electronics Thailand Ranked Among Asia’s Top Corporates at the Alpha Southeast Asia 15th Institutional Investor Awards
07/14/2025 | Delta ElectronicsDelta Electronics (Thailand) Public Company Limited, a global leader in power management and smart green solutions, has been recognized by global investors for its excellence in investor relations and corporate governance, earning top ranking in the “Most Improved Investor Relations” at the Alpha Southeast Asia 15th Annual Institutional Investor Awards for Corporates, held on June 30, 2025, in Singapore.
Kimball Electronics' Pride Month Celebrations
07/14/2025 | Kimball ElectronicsAt Kimball Electronics, we believe in fostering a culture of inclusion, respect, and belonging. This June, our global teams came together to celebrate PRIDE Month with meaningful actions that reflect our commitment to the LGBTQ+ community.
NOTE Posts Interim Report for Q2 2025
07/14/2025 | NOTENOTE reports stable second-quarter results for 2025 with continued profitability and strong cash flow, reaffirming its growth strategy despite a challenging market environment.
Scanfil, MB Elettronica to Join Forces
07/14/2025 | ScanfilFinnish Scanfil, the largest European stock exchange listed Electronic Manufacturing Service company in terms of turnover, and Italian MB Elettronica (“MB”) from Cortona Arezzo have agreed to join forces.
PCBAA’s David Schild: Where U.S. Electronics Manufacturing Stands Today
07/14/2025 | Marcy LaRont, I-Connect007As the U.S. Congress looks toward a summer break, David Schild of PCBAA discusses the growing momentum in U.S. electronics manufacturing policy, emphasizing bipartisan support for reshoring efforts, the importance of targeted tax incentives, and the challenges posed by global competition. He highlights PCBAA’s growth, advocacy on Capitol Hill, and the need for sustained investment to revitalize the PCB industry.