Material Insight: David Griesel: Career Success Requires Tenacity, Flexibility
It's Only Common Sense: The Election Isn’t Your Problem
Dan’s Biz Bookshelf: ‘The Wizard and the Warrior: Leading with Passion and Power’
NCAB Advocates for Advanced Technologies
May 17, 2023 | Andy Shaughnessy, Design007 MagazineEstimated reading time: 3 minutes
At the SMTA Atlanta Expo and Tech Forum, I spoke with NCAB Group Field Application Engineer Ramon Roche, who gave a presentation at the show titled, “Technical Trends in the Global PCB Industry.” Ramon and I discussed his presentation, the emerging technologies that have NCAB’s focus over the next few years, and why semi-additive processes may be the key to succeeding with ultra HDI technology.
Andy Shaughnessy: Nice to meet you, Ramon. Why don’t you start off by telling us about your presentation?
Ramon Roche: Nice to meet you too, Andy. Sure. I came to Atlanta today to talk about emerging technologies in the PCB industry, and really take a deeper dive into ultra HDI and how we see this disrupting the industry. We touched on some of the market trends and some current applications, and some challenges that we're seeing in sourcing and on the manufacturing side. Basically, for this new technology, what do we have to do to be prepared to make ultra HDI a reality?
Shaughnessy: What are some of the steps that that you all need to take to ramp up for ultra HDI?
Roche: We’re partnering with our customers to take small steps forward into this unchartered territory. During the presentation, we talked about IPC’s HDI spec, which only goes down to 50 microns, while ultra HDI goes well below 50 microns—down to 30 microns and even 20 microns in some cases. There’s no standard in place for ultra HDI just yet. We’re working with our customers to not only design, appropriate applications for this, but also asking ourselves, “How do we as an organization work with our manufacturing partners as well to succeed at that level?”
Shaughnessy: So, if you’re going to move into ultra HDI, do you have to use additive processes like A-SAP or m-SAP? Subtractive processes aren’t practical or even possible at that level, correct?
Roche: Absolutely. The first thing you have to do is put your cowboy hat on, because there’s a lot to learn about the design aspect of it. And then on the manufacturing side, you have to work with your local reps or FAE and have a conversation. Once you get below 50 or 40 microns, your traditional subtractive manufacturing methods are starting to reach their capacity, so we have to utilize different manufacturing methods to accomplish this. Below 40 microns, it’s time to consider semi-additive processes—A-SAP or m-SAP—for these very fine lines.
Shaughnessy: What was the reaction to the presentation attendees? Did you have any good questions?
Roche: Yes, we had a very interactive class, and a lot of really great questions, really pushing the boundaries as engineers. A lot of the questions and concerns that came up were about the robustness and reliability of these boards as they continue to get smaller and smaller. And those are things that we're still gathering data on because we want to improve our yields while making sure that we're building robust boards. We talked about some of the different considerations involving materials with semi-additive processes. And we discussed advanced embedded trace substrates, which can take you below 20 microns, and some different manufacturing processes that allow us to condense all of this into a small footprint. It’s exciting stuff.
Shaughnessy: Do you think semi-additive will eventually make up a big chunk of the market?
Roche: Yes. Semi-additive is a much cleaner and greener process than subtractive etch. There's a lot of pressure from governments and society in general to embrace sustainability, and semi-additive is a huge improvement over etched copper in that regard. And there are cost reductions as well, just with photoresists and electricity, to name a few. All of this makes this process more impactful as we incorporate this in the future.
Shaughnessy: Sounds good. Thanks for speaking with me, Ramon.
Roche: Thank you, Andy.
Share on:
Suggested Items
The Cost-Benefit Analysis of Direct Metallization
10/21/2024 | Carmichael Gugliotti, MacDermid AlphaCarmichael Gugliotti of MacDermid Alpha discusses the innovative realm of direct metallization technology, its numerous applications, and significant advantages over traditional processes. Carmichael offers an in-depth look at how direct metallization, through developments such as Blackhole and Shadow, is revolutionizing PCB manufacturing by enhancing efficiency, sustainability, and cost-effectiveness. From its origins in the 1980s to its application in cutting-edge, high-density interconnects and its pivotal role in sustainability, this discussion sheds light on how direct metallization shapes the future of PCB manufacturing across various industries, including automotive, consumer electronics, and beyond.
Connect the Dots: Designing for Reality—Pattern Plating
10/16/2024 | Matt Stevenson -- Column: Connect the DotsIn the previous episode of I-Connect007’s On the Line with… podcast, we painted the picture of the outer layer imaging process. Now we are ready for pattern plating, where fabrication can get tricky. The board is now ready to receive the copper traces, pads, and other elements specified in the original CAD design. This article will lay out the pattern plating process and discuss constraints in the chemistries that must be properly managed to meet the customer's exacting manufacturing tolerances.
PCB007 Magazine October 2024: Alternate Metallization Processes
10/16/2024 | I-Connect007 Editorial TeamTraditional electroless copper and electroless copper immersion gold have been primary PCB plating methods for decades. But alternative plating metals and processes have been introduced over the past few years as miniaturization and advanced packaging continue to develop taking us into new directions. In this issue of PCB007 Magazine, we examine the impact of alternate metallization methods giving a glimpse into how and when we will arrive at 'destination metallization'.
Partial HDI: A Complete Solution
10/10/2024 | I-Connect007 Editorial TeamWe recently spoke with IPC instructor Kris Moyer about partial HDI, a process that’s recently been growing in popularity. Partial HDI allows designers to escape route out from tight-pitch BGAs on one layer, where a mechanically drilled plated through-hole is not an option, while avoiding the complexity and expense of sequential lamination cycles. As Kris explains, this process doesn’t add much to the cost, and it’s fairly straightforward. But there are some competing signal integrity and fabrication requirements to contend with. We asked Kris to walk us through this process.
Trouble in Your Tank: Interconnect Defect—The Three Degrees of Separation
10/01/2024 | Michael Carano -- Column: Trouble in Your TankIt has been well documented that, with a very expensive and complex printed circuit board, thermal and mechanical excursions often find weaknesses. A lack of robustness and poor process control often leads to the exploitation of those weaknesses. An interconnect defect (ICD) often goes undetected until the printed circuit board reaches the final assembly stage or undergoes multiple thermal cycles, including interconnect stress tests or thermal shock. It is impossible to rework the ICD defect. But unlike voids, if detected in time, the panels can be reprocessed.