Challenges of DFM Analysis for Flex and Rigid-flex Design, Part 2
May 18, 2023 | Mark Gallant, DownStream TechnologiesEstimated reading time: 2 minutes

(Editor’s note: This is the second of a three-part series. To read Part 1, click here.)
Flex and Rigid-Flex: Different Layer Types
Everyday rigid FR-4 PCBs have a well-known layer stackup recipe: dielectrics, PCB conductor layers, plane layers, mask, and silkscreen (nomenclature or legend). More advanced layer types may include embedded or screened components or cavities with bonded bare die.
Flex and rigid-flex stackups include those similar to rigid PCBs, such as dielectrics, conductor, mask, and silkscreen layers, but that is where the similarity ends. There are many additional layer types present for this genre of PCB. They include types like coverlay, adhesive, conductive film, conductive foil, conductive adhesive, bondply, and stiffener.
- Coverlay: An external polyimide film that encapsulates and protects flexible conductor layers.
- Adhesive: Bonding agent used to bond copper foil to a polyimide substrate or coverlay.
- Conductive film: Transparent but electrically conductive film found in LCDs, touchscreens, and other optical applications.
- Conductive foil: Thin sheet of copper or silver commonly applied to a flexible PCB as shielding.
- Conductive adhesive: Adhesive applied for electrical interconnect, thermal or structural bonding applications.
- (Flexible) bondply: A polyimide film, coated both sides with B-staged acrylic adhesive. This is essentially a coverlay with adhesive on both sides.
- Stiffener: Blank FR-4 or other material bonded to flexible materials to add stiffness in a specific area.
These layer types are found in typical flexible PCB stackups. The presence of these layer types is not accounted for in most current DFM analysis. This is one area where specific DFM analysis is required. Rigid DFM analysis can detect issues with a solder mask but cannot be used to detect trace corners in a bend area.
Inter-layer Dependencies
While less common in rigid PCBs, flexible PCBs have many inter-layer dependencies that, if not managed well, may lead to manufacturing issues or field failures. The fabrication process used to bond rigid and flexible layers also has its inter-layer dependencies to be managed. Here are a few examples of inter-layer potential issues.
Squeeze-out
Even with best design considerations and best manufacturing practices, adhesive can “squeeze out” and bleed into unwanted areas on adjacent layers. Coverlay adhesive is a common source of squeeze-out that flows during lamination onto conductors, pads, cavities, fingers, or other features. This requires analysis that compares the size of coverlay exposure against the annular ring of adhesive below it.
To read this entire article, which appeared in the May 2023 issue of Design007 Magazine, click here.
Suggested Items
Indium Corporation Hires New Sales Engineer
12/06/2023 | Indium CorporationIndium Corporation is proud to announce the addition of Sales Engineer Meik Fratzel to its European team.
Transition Receives Large Order for Advanced Squeegees from Rotec BV
12/04/2023 | Transition AutomationTransition Automation, Inc. recently received a large order for Advanced Holder and Blade Assemblies compatible with DEK printers from Rotec BV in Belgium.
AIM Debuts New NC259FPA Ultrafine No Clean Solder Paste
11/30/2023 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its new NC259FPA Ultrafine No Clean Solder Paste, which it revealed recently during the Productronica Germany trade show.
Real Time with... productronica 2023: Koh Young Discusses Semiconductor and Advanced Packaging Inspection
11/27/2023 | Real Time with...productronicaKoh Young’s Harald Eppinger talks about the company’s technology for the semiconductor and advanced packaging market and how they address the challenges introduced by reflective components and micro solder deposits.
HyRel Technologies Attains ITAR Registration, Reinforcing Leadership in Robotic Solder Component Tinning
11/27/2023 | HyRelHyRel Technologies, a global provider of quick turn semiconductor modification solutions, announces the achievement of International Traffic in Arms Regulations (ITAR) registration.