Driving Innovation: Mechanical and Optical Processes During Rigid-flex Production
It’s Only Common Sense: Your Biggest Competitor Is Complacency
The Chemical Connection: Onshoring PCB Production—Daunting but Certainly Possible
Electrical Testing of Passive Components
September 2, 2014 |Estimated reading time: 1 minute
Introduction
Substrates have become more critical with regard to pitch and density in today’s designs with challenges for passive components in terms of surface placement. This negates the opportunity for high speed, high cost components to be placed on the surfaces of the PCB. With this the capacitance and resistive components have to be embedded into the design. This has been accomplished with the advent of buried capacitance cores and buried resistors. Unfortunately, this has caused some challenges to the ET test centers/labs in the ability to effectively test these buried passive components. Processes have had to change and adapt to these new technologies. The paper will discuss what these new technologies are and how the electrical test arena has adapted to provide accurate testing of the buried resistors and accommodate the buried capacitive cores to not receive false errors from the grid testers and flying probes.
Resistors
In the past, pull-up, terminating and voltage dividing resistors have been placed on the surface of the PCB. Early applications were standard carbon resistors placed on the board utilizing plated through-holes.
As can be seen in Figure 1, the standard carbon resistor took up a lot of space on the PCB. You will also notice in the photo that capacitors are also stealing valuable space from the surface topography. As time progressed, SMT technology was introduced and the older, bulky standard carbon resistor was replaced by the newer SMT packages (Figure 2).
This was a very popular innovation to the industry as now the surface footprint was drastically reduced and the topography on the surface of the PCB was now open to accommodate more active components which reduced the overall size of the PCB, but also allowed the complexity of the designs to grow. No longer was a PTH as needed for the resistor, which allowed the multilayer to expand its capabilities on the inner layers to provide not only an overall smaller PCB, but a more powerful final product.
Read the full article here.
Editor's Note: This article originally appeared in the July 2014 issue of The PCB Magazine.
Share on:
Testimonial
"Your magazines are a great platform for people to exchange knowledge. Thank you for the work that you do."
Simon Khesin - Schmoll MaschinenSuggested Items
TTCI Brings Hands-On Test Engineering and IPC Training Expertise to PCB Carolina 2025
10/31/2025 | The Test Connection Inc.The Test Connection Inc. (TTCI), a trusted provider of electronic test and manufacturing solutions, and The Training Connection LLC (TTC-LLC) will exhibit at PCB Carolina on Wednesday, November 12, 2025, at the McKimmon Center at NC State University in Raleigh, North Carolina. Attendees can visit Table 4 to say hello to Bert Horner and Bill Graver, and learn more about their test engineering services and technical training programs.
GEN3 Systems to Showcase Advanced Reliability Test Solutions at productronica 2025 in Munich
10/29/2025 | Gen3 SystemsGEN3 a leader in innovative reliability test solutions, is excited to announce its participation at productronica 2025, the world’s premier trade fair for electronics development and production.
Unlocking the Promise of AI in Electronics Manufacturing
10/29/2025 | Shobhit Agrawal, Keysight TechnologiesThe electronics manufacturing industry is rapidly evolving as more complicated products are introduced in the production lines, which require technological advancements even in the production processes. The requirements for production that is efficient, product quality that is greater, and product life cycles that are shorter are more crucial than ever before. In the electronic device life cycle, from design to maintenance, test phases have a significant impact on the economy of the company. Test processes are closely linked to the production volume and impacted by the complexity of the product. For businesses to maintain their competitive edge, they need to adopt innovative solutions and redefine processes.
New Episode of Voices of the Industry Podcast Explores Breakthroughs in Test and Inspection
10/22/2025 | I-Connect007In this episode of Voices of the Industry, “Testing Innovation: Advances in Test, Inspection & Failure Analysis,” host Nolan Johnson speaks with Rob Boguski, president of Datest. Together, they explore the expanding world of circuit testing, inspection, and failure analysis, areas that are experiencing a surge in technological capability and sophistication. As Johnson and Boguski discuss, today’s test companies are performing analyses and precision methods that would have seemed impossible just a decade ago.
HT Global Circuits Adds Two atg Luther & Maelzer Flying Probe Test Systems
10/15/2025 | atg Luther & Maelzer GmbHAtg Luther & Maelzer GmbH, a leading supplier of electrical testing solutions for the PCB industry, and IEC USA, a distributor of consumables, equipment, and services in the North American PCB market, confirm the order for high-speed bare board testing technology.