Robot to Ensure Oxygen Supply to COPD Patients
February 13, 2017 | DTUEstimated reading time: 3 minutes
DTU Electrical Engineering, the Danish company PACTOR, and Senior Consultant Ejvind Frausing, Hvidovre Hospital, have jointly developed a robot that can monitor the content of oxygen in the blood of COPD patients. Unlike healthy persons, COPD patients cannot tolerate excessive oxygen levels in their blood, as it may impair their breathing. Too little oxygen is also dangerous, because it damages the organs of the body and—in a worst-case scenario—severe oxygen deficiency may be fatal. It is therefore important that these patients are treated with the right oxygen amounts, as both too much and too little oxygen is harmful.
“Currently, nurses monitoring patients continuously are responsible for checking that they receive the right oxygen amounts. But this creates great uncertainty, as undetected changes may occur in between the nurses’ checks. Therefore, the robot will increase patient safety," explains Ejvind Frausing, Senior Consultant at the Medical Unit, Hvidovre Hospital, who came up with the idea for the robot.
"At the same time, this will allow nurses to spend time on other healthcare tasks, and inpatient stays can be shortened. The oxygen robot will consequently result in both care quality and financial improvements".
The O2Matic robot consists of a small box that receives data every second from measurements of the oxygen content in the blood via a clamp on the patient’s finger and a bracelet around the patient’s wrist. The robot can subsequently adjust the amount of oxygen supplied. In case of major changes in the patient’s condition, the robot will send an alarm to the staff.
Iltrobotten til højre - den lille kasse, der viser et iltindhold på 94 % - afprøves her på Herlev Hospital på en patientsimulator med KOL.
Doctor’s knowledge encoded in the robot
DTU has contributed to the development of the robot—both the concept and software development. The latter has comprised the coding of the robot with the doctors’ knowledge about what the robot is to do, e.g. if the patient’s pulse drops. In addition, DTU has contributed to building the robot so that it consists of the most optimal components.
“We can see that greater automation elsewhere in the healthcare sector can also improve patient safety and free up staff to perform other assignments. The development is progressing rapidly, and, in our research, we work with robots that are not only able to carry out very well-defined tasks in a fixed framework, such as mowing grass in a fenced-in area. Our new robots are also capable of reading the surroundings and responding to changes in them, so that they become much more usable for more ‘intelligent’ tasks, both in industry and at hospitals,” explains Associate Professor Ole Ravn, Head of Automation and Control at DTU Electrical Engineering.
He sees great potential in automation in the healthcare sector and expects that, before long, other robots will be developed for special monitoring tasks.
The oxygen robot on the right—the small box showing an oxygen content of 94%—here during testing at Herlev Hospital on a COPD patient simulator.
Next step: the world’s largest oxygen treatment trial
In the course of 2017, the oxygen robot is to undergo a number of tests in order to be finally approved for patient use. The robot will then be included in the world’s largest oxygen treatment trial on humans, which will be conducted among COPD patients in a number of hospitals in Denmark.
"We will then be ready to produce and sell the oxygen robot, both in Denmark and abroad. Today, there is no similar automatic oxygen device, so we expect great interest," says Director Farzad Saber from the Danish company PACTOR, which has participated in developing the robot.
In the long term, the intention is also to develop a version of the robot which can be used by patients at home, thereby reducing the number of admissions.
Suggested Items
Real Time with… IPC APEX EXPO 2024: My Role as a Technology Solutions Director
05/02/2024 | Real Time with...IPC APEX EXPOPeter Tranitz, senior director of technology solutions at IPC, shares insights into his role as the design initiative lead. He details his advocacy work, industry support, and the responsibilities of the design initiative committee. The conversation also covers the revamping of standards, the IPC Design Competition, and the implementation of design rules in software tools.
Seeking Employment: Palash Pranav Vyas
05/03/2024 | Barry Matties, I-Connect007Despite skilled worker shortages across the industry, there are many educated and qualified individuals ready to contribute to electronics manufacturing. Here we profile Palash Pranav Vyas, a Ph.D. candidate at Auburn University whose work in drop shock reliability won him Best Student Poster at IPC APEX EXPO 2024.
iNEMI Names Grace O'Malley CTO
05/02/2024 | iNEMIThe Board of Directors of the International Electronics Manufacturing Initiative (iNEMI) has named Grace O'Malley Chief Technical Officer (CTO).
Gartner Survey Finds 61% of Organizations Are Evolving Their D&A Operating Model Because of AI Technologies
05/01/2024 | Gartner, Inc.Sixty-one percent of organizations are forced to evolve or rethink their data and analytics (D&A) operating model because of the impact of disruptive artificial intelligence (AI) technologies, according to a new Gartner, Inc. survey.
GPV’s Q1 2024 Interim Financial Report Shows Strong Navigation in Uncertain Times
05/01/2024 | GPVDanish-based GPV recorded an expected drop in sales to DKK 2.3 billion for the first quarter of 2024. The decline also affected the operating profit, which was DKK 155 million compared to DKK 179 million in the same quarter last year, although the EBITDA margin was maintained. In general, demand has been softer in 2024, but GPV continues to invest for the long-term and expects the trend to turn in the second half of 2024.